WHAT HAVE YOU DONE TO YOUR 3RD GEN TUNDRA TODAY?

Yes, it replaces the crash bar that was there prior.

 

Rainbow Falls and Rampart Crossing. Leads to Mini Moab

 

What is the lead time on their lifts?

 

I think it a great idea, don’t worry about what people say. The red looks good to me, but your truck do what you like! That’s why it’s your!

 

Love that trail!

 

Finished the install of my CBI Baja Bumper over the weekend. More pics & info in my build thread, but wanted to share here since it's been awhile since I posted in the "What Have You Done To Your 3rd Gen Tundra Today" thread.

Build Thread: Duster's Double Cab Build - The Daily Do-it-All

 

How much weight can one of these steps support?
- Big Boy

 

I’m not sure if the power step is different, but the manual step is rated for 300lbs. I’ll tell you that I’m a big guy too and my manual step feels rock solid when I use it.

 

Out with the old in with the new haha.

Surprised how quiet this truck is compared to my 2020.

Wasn’t too sure about the lunar rock at first but now I’m pretty happy with it.

just put a deposit on a smart cap anyone have any experience with them?

Gonna color match the mustache and bumper caps and debadge it this week too

 

I was the same about Lunar Rock. I loved my Cement Taco. I call Lunar Rock “Cemint” because of the greenish hue. But after taking delivery of it, it looks great! Especially with a wrap.

 

Just a little update

 

Damn those tires are aggressive what are those?

 

They are Gladiator x comp MT. They ended up being defective after 3 months of dealing with manufacture they finally refunded due to
Out of round. I just mounted Toyo Open country MT. The ride is night and day. I loved the look of these tires but the ride quality was terrible.

 

Those gladiators are terrible tires they don’t balance for shit and wear in 20k miles. Toyo MTs are great occasionally you’ll find a tire that pulls right so watch out when you rotate

 

Great looking but good for nothing, lol. Thanks for the heads up on that. I’m running 30psi in tears and 35 in front.

 

Which bed step is this? Thanks!

 

I have the Toyo AT3 my 2nd set after running 4 sets of MTs my last set of MTs could not get them to stop pulling on my Tacoma. I run 37 psi all the way around

 

P/N is

$154 PTS3034000 PTS30-34000 Folding Truck Bedstep Compatible with Toyota Tundra(2022-2024), Retractable Rear Bumper Step, Easy-to-Install, Non-Slip, Corrosion-Resistant

PTS3034000. It's the manual OE bedstep from Toyota. I installed it on my truck and it's great. It does reduce departure angle slightly, but the trade off is worth it. IMO.

Pics of it on my build thread, if it helps.

 

Looks sweet! What did you wrap it in?

it is totally cemint hahah

 

Installed Air-Lift Ultimate 5000 air bags along with the Air-Lift WirelessONE air pump/controller. Installed an additional T at the passenger side rear airline and ran a manual fill valve to the receiver hitch mount where there is already a hole drilled. This will allow for manual fill in the event of a compressor failure, or if I need to reference the actual PSI for troubleshooting, using a physical gauge. It was quick and easy, and all the parts came with the kit, so figured why not. Compressor is mounted to the outside frame rail, just below the rear passenger door. I ran the fresh air intake for the compressor into the cab, as there is a wiring harness entry point in the same location that goes directly into the cab, and under the rear passenger storage compartment. Easy access with just a few clips to remove. All airline and wiring harness was put in a braided loom to prevent abrasion, although not necessary. Used a handful of extra 'christmas trees' to secure both the wiring loom and airline along their routes.

Also swapped the front grill surround with a color matched surround, and changed the TRD Off-Road grill insert for a TRD Pro grill insert. I've had a piece of window trim on back-order for two months now, but once that piece arrives, i'll swap out all 6 of them for a matte black window trim. I might try wrapping the door handles, but havent quite made up my mind there yet.. Slowly but surely, she's coming along!

 

Installed ********* cat shield today.

Take that you thieving bastards!




Next up Charvonia bed tie downs on Friday.

Then snow tires - Blizzaks on black alloy rims.

The truck investments continue…..

 

What the heck is up with this?? That bolt is way too long

 

Milwaukee leaf blower. I see you're a man that enjoys the finer things in life.

 

So not today, but Saturday I finally got to take the new truck home after they replaced the Passenger mirror damaged in transit. Loving this Truck so far!

 

Ah yes, it and the mower have exceeded my expectations and then some

 

Love it, looks incredible

 

I put on the Truxedo Sentry Ct tonneau cover, TVD decals on the rear, Go Rhino RB20 slims, and also upgraded to 285 75 18's. Love the new stance and no rub with the tires.

 

Installed 1.75" leveling kit.
Exactly level, maybe 1/4” lower in front at the most, depending on where and how I am parked. Will measure again on exactly flat surface.

 

Sorry to break it to ya but a 1.75 RC will give You a lean from the front being higher. Judging by the second pic yours is slightly higher in the front

 

Looks great