1. Welcome to Tundras.com!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all Tundra discussion topics
    • Transfer over your build thread from a different forum to this one
    • Communicate privately with other Tundra owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

Cali Raised Dual LED Light Bar

Discussion in '2.5 Gen Tundras (2014-2021)' started by Username, Jan 2, 2021.

  1. Jan 13, 2021 at 3:43 PM
    #31
    Cruzer

    Cruzer Wheeling Full Size

    Joined:
    Oct 12, 2020
    Member:
    #53461
    Messages:
    3,126
    Gender:
    Male
    First Name:
    Cruz
    Sunnyvale, CA
    Vehicle:
    Build Page: Cruzer's Re-Build for the Rubicon
    The bracket bolt sits on it. Picture is of the driver side.
    upload_2021-1-13_15-43-25.jpg
     
  2. Jan 13, 2021 at 3:54 PM
    #32
    Username

    Username [OP] New Member

    Joined:
    Oct 18, 2019
    Member:
    #37542
    Messages:
    109
    Gender:
    Male
    First Name:
    Joe
    Boise ID
    Vehicle:
    2021 Army Green Turd-ra
    Lost track of shit
    I am talking about the push pin tabs on the bulge in the upper corners, I might need to push the led light bar back a little bit from your picture.
     
  3. Jan 13, 2021 at 10:32 PM
    #33
    Username

    Username [OP] New Member

    Joined:
    Oct 18, 2019
    Member:
    #37542
    Messages:
    109
    Gender:
    Male
    First Name:
    Joe
    Boise ID
    Vehicle:
    2021 Army Green Turd-ra
    Lost track of shit
    @Cruzer

    Did yours ever hit in these areas?

    My is making contact against each other at these points.

    962E1327-D2F2-4228-8341-FE9DDFC5F6AA.jpg
    4C9DF932-24D4-4426-B054-C537C518FCD0.jpg
     
  4. Jan 14, 2021 at 8:17 AM
    #34
    Cruzer

    Cruzer Wheeling Full Size

    Joined:
    Oct 12, 2020
    Member:
    #53461
    Messages:
    3,126
    Gender:
    Male
    First Name:
    Cruz
    Sunnyvale, CA
    Vehicle:
    Build Page: Cruzer's Re-Build for the Rubicon
    On the Youtube video you had to chop off the end mounts:
    upload_2021-1-14_8-16-10.jpg

    Since you no longer have a hole to mount it to then you can go ahead and cut off what you need to make it fit:
    upload_2021-1-14_8-17-0.jpg
     
    Username[QUOTED][OP] likes this.
  5. Jan 14, 2021 at 8:21 AM
    #35
    pearlpower

    pearlpower New Member

    Joined:
    Jul 14, 2020
    Member:
    #49315
    Messages:
    214
    Vehicle:
    2014 CrewMax in Radiant Red
    The bulge surround hits the light, has nothing to do with the vertical hood support members. I set mine back where the side mounting brackets were just past the body panel, not in front as in the pic above. However, I took some needle nose pliers and bent the side hood metal to go in front of the mounting bolts. This will set the light further back. Also, some trimming of the clip holder on the surround needs to happen to get it to sit flush on both ends.

    For others, a shorter light would not suffer this. Just the light in this thread as it is long.
     
    Username[OP] likes this.
  6. Jan 14, 2021 at 8:21 AM
    #36
    Username

    Username [OP] New Member

    Joined:
    Oct 18, 2019
    Member:
    #37542
    Messages:
    109
    Gender:
    Male
    First Name:
    Joe
    Boise ID
    Vehicle:
    2021 Army Green Turd-ra
    Lost track of shit
    Makes sense now, thank you very much. I had enough room I did not need to chop the tab off to fit the bar and was still trying to use it.

    So I just need to chop off the tab and the clip.

    Thank you sir.
     
  7. Jan 14, 2021 at 8:23 AM
    #37
    Cruzer

    Cruzer Wheeling Full Size

    Joined:
    Oct 12, 2020
    Member:
    #53461
    Messages:
    3,126
    Gender:
    Male
    First Name:
    Cruz
    Sunnyvale, CA
    Vehicle:
    Build Page: Cruzer's Re-Build for the Rubicon
    :hattip:
     
    Username[QUOTED][OP] likes this.
  8. Jan 15, 2021 at 2:43 PM
    #38
    LA184

    LA184 Living the Dream

    Joined:
    Sep 11, 2020
    Member:
    #52092
    Messages:
    58
    Gender:
    Male
    Vehicle:
    2014 4x4, 4.6L Radiant Red Tundra
    4 in lift, 35s, Black Rhino Armory Wheels, Custom Rock Sliders, SDHQ ABS Guards, Warn Winch Bumper, Warn Evo VR 12-S Winch, 4.88 Re-Gear, Rear E-Locker.
    Your grill and the TRD Pro grill work the best with the dual light bar set up. I have a different grill, and although some of the light is blocked, the output is incredible. If cost is your concern, Amazon has some good options for a fraction of the cost. All together, my set up cost me around $150-$200, including brackets and both lights. Did the install with a friend who knows wiring.
     
    Username[QUOTED][OP] likes this.

Products Discussed in

To Top