2022 Tonneau covers

I've found their customer service off the charts. The rear seal on my 'soft' TruxEdo finally cracked after 5 years. Went to the web-site to find a part number to order a new one .. couldn't find it .. called them and asked. They just asked my address and sent me out a new one immediately. Wonderful service!!

DWS

 

$1,200 Syneticusa Automatic Retract Hard Tonneau Cover Fits 2022-2023 Toyota Tundra 5'6" (66.7”) Truck Bed Aluminum Matte Black Low Profile Waterproof Off Road Rack Ready Retractable

Amazon.com: Syneticusa Automatic Retract Hard Tonneau Cover Fits 2022-2023 Toyota Tundra 5'6" (66.7”) Truck Bed Aluminum Matte Black Low Profile Waterproof Off Road Rack Ready Retractable : Automotive

 

How are you liking this? Do you have a link to the seller (I couldn't find one at the price you quoted). Can you still use the track system? Thanks!

 

It's listed for 334.99. I offered 300 they countered with 318. You can still use the track to some extent w/o removing anything. Loving it still, pretty hard rain the other day and very little water made it in the bed. One of the foam blocks popped off but easily fixed w some epoxy. I think i may get some better track clamps
Extang 22440104 Clamp Kit
https://www.ebay.com/itm/2948035203...cMn-mm0QGe&var=&widget_ver=artemis&media=COPY

 

For those with 2022 branded tonneau covers vs 2021 and prior, are they mounted the same? Are they all using brackets similar to this? I bought a hard trifold 6.5 advertised as 2007-2022 tundra. Assuming I may need to fiddle with the mounting. Got the cover already actually but don’t have the truck yet so can’t check it out.

 

Mounting clamps are different for 22 but you can use these for previous gen covers.

 

Get these they work awesome https://www.etrailer.com/Accessories-and-Parts/Extang/EX22440104.html

 

I also have the TruXedo Sentry CT on my 22 Tundra, had it on the 20 Taco, love it and the rail cleats still work for both.

 

Thanks!

 

Anyone with a 2022 factory tri-fold hard cover having issues with pooling in the bed? I've had it in to the dealer twice and they keep telling me that "Toyota states the amount of water is acceptable". Recommendation on experience resolving such issues would mean the world. I've sent a message in to Toyota.com but haven't heard back as of yet.

 

Yup

 

There should be 4 drain holes 2 are being used for tonneau drains it looks like. The other 2 should be closer to the corners & may be plugged/ clogged or if you have bedliner sprayed in which it looks like you have, they may be sprayed over. Find ‘em & drill them out.

 

I have the OEM tri-fold. Came with the truck, and I've managed through the PNW rain with a dry bed. Looks like I have the same crossed drain tube setup in your pic (2 tubes total).

Did you try sliding the whole cover up towards the cab more? I've taken it off/on a few times and there's about 2 inches wiggle room that would allow you to slide towards the front or back.

 

Where in LA? I’m on the Northshore. I saw a truck similar to yours (same color at least) in Mandeville about a week ago.

Back on topic; I am picking up a bed mat tomorrow and have a BAKflip MX4 coming Wednesday, so I am anxious to see how it does with the daily afternoon rain as well.

 

My cover leaks this bad as well. However my drain tubes and holes are clear. So no pooling. Still a mess of water coming in at the folds on the cover soaking my bed. Waiting to hear back from dealer about warranty.

 

Love the OEM tri-fold, however, i do get a bit of water in the cab corners... not sure its enough to make me worry about it though. Im sure i could come up with something to remedy, or perhaps give the dealership a chance during my 5K mile inspection....

Heck, even Gortex leaks after a while...

 

I apologize if someone already asked this, but does anyone have a retrax yet? I have one sitting in my garage, just waiting on the truck.

 

Pretty sure @tunfundra has one and loves it

 

I had one waiting. Then I passed on the pro. Then I returned the cover. Now I have a pro coming again.....

 

Pro is in! Got the diamondback hd cover on with the Yakima jet stream crossbars. I should have waited till it was a little bit cooler to install, sweated my tail off in the bed tightening everything up.

 

Cover looks awesome! Also digging the GAP sticker.

 

Got my BAKFlip MX4 put on this morning. So far so good. Took it for a little test drive up to 80 or so and everything is quiet. I think it has been mentioned before, but the factory drain holes definitely need to be drilled out a little bigger for the drain tubes and I went even a little extra for just regular drainage from the bed of course.



Also picked up an OEM bed mat yesterday at another dealership nearby.

 

Walked to my truck this afternoon and thought the velcro had come apart on my Access Tonnosport cover. When I got closer I realized that actual adhesive holding the velcro to the bed rail had failed.
Not even 5 minutes on the phone with Access and they had a replacement velcro strip coming for me to replace it. A little disappointing for a 3 week old cover, but hopefully it's just a fluke. Their customer support was A+ though.

 

Is your tailgate insert black and red?

 

This may be a dumb question, but how does it open? Roll up?

 

Yes it’s a roll up cover.

 

I'm in the same boat! Got my retrax.. just waiting on my 1794..now a bit longer with with the QC

 

Update on my BAKtrak MX4.
We drove 650mi or so total yesterday and today for a quick trip into Alabama and back for a graduation ceremony.
Today on the way back it rained and even poured on us for certain stretches pretty much the entire way from Ft Rucker to Louisiana.
Only a tiny bit of water got in at the very back by the tailgate and even that was minimal.
Very Impressed.

 

did you say you had to drill out the factory drain holes even wider? Got pics?

 

I have a Bakflip F1 cover that leaks quite a bit across the seams between the panels. I contacted Bakflip and they say it is a defect and sending whole new unit. I'm pretty sure Bakflip makes the OEM cover, so you may have the same issues. I will say, the customer service from Bakflip seems pretty good at face value.....I don't have my new cover yet, so we'll see!