1st Gen. Lunch Table - General Discussion

I paid $131 shipped to get the part circled in blue, complete with cables and everything. The only thing I had to transfer over from my original latch assembly was the part in green.

 

Inside the EPC, the Sequoia uses different INDEX numbers than the DC, but the part numbers are technically the same.

Here is the difference for an '05 DC versus an '05 Sequoia, notice the part index numbers (in the colored boxes) are different, but the physical part numbers are identical - once again, you may only need the LATCH, not the ASSEMBLY, one is 3x more $$ than the other:

​

 

Torching the evidence of the great box building adventure

 

Uh oh, i seem to have found a map to my next money pit.


I want a mazda az1. Or a kei van. Or dihatsu midget…i dont know what i want.

 

Subaru makes em too.

I was looking the other day (out of curiosity) and finding one with a title is not easy.

 

The VA has a few of them, and some vans, all manuals. Tiger trucks or something. I want a van with a mid mounted K24. With a whipple.

 

Y'all should just get a job at a college or stadium and get paid to drive one.

 

We have one at work that the bed raises like a scissor lift

 

That's pretty cool. Can it be used as a dump bed too?

 

I’m not sure, it definitely seemed like a landscaper type setup though. If I see it around I’ll ask

 

Yeah this one I looked up has both:

https://www.youtube.com/shorts/mJ5jOWoWtx4

 

Honda acty with a k engine

 

This is the way.

 

Grammar is important.

 

What I found as odd after a got my tundra: They look like a midsize truck compared to todays modern trucks unless you're up close, or they're side by side; BUT I couldn't stand it and hd to pull a tape.....
The interior measurements between the Tundra and a 2018 gmc double cab 4x4, are so close as to be negligible.
The tundra has more ground clearance and is higher at the top of bed by about 6 inches at the tailgate. Top of tailgate height of gmc is 54. Tundra is 59.5.

 

FGT is right sized.

 

I have been tentatively looking for left front (driver side) inside door handle and trim piece to replace one I broke.
Also need clips that hold the passenger side exterior handle in place. It still good on front portion but back will pull away from the door.
Where's the thread where I can find these?

 

Sit in a midsize truck and you will instantly be able to tell they're smaller than our best gen Tundras. Cramped AF compared to our extra room

 

https://www.tundras.com/threads/howto-use-the-toyota-parts-system-to-find-order-parts.113808/

1st couple bullets. Your part will be in the Body section. Then in front door or rear door subsection.

Note a lot of color matched interior parts are gone now. Being replaced with tan/beige. Dunno why.

 

On the EPC it’s showing the tundra part number as 69304 but on ourismans Toyota website the numbers are the same for the sequoia part. Weird

 

Hey I’m looking to remove my differential drop, if any has the part numbers to the shorter bolts or point me in a direction I could find them.

 

My dad had a Suzuki Carry Kei truck, manual, 4x4 etc. it was pretty fun to drive, but oh so uncomfortable too. Sold it a couple years ago.
They’re all over up here (with titles), start importing them to the south, might be profitable if there’s demand. I think they basically age out in Japan so there are a few importers bring them over when they hit a certain age.
There are a number of Subaru Sambars around with body kits to look like a VW bus, kinda fun.

 

That's the exact part number that I bought from a different dealer for my driver's door. When I search on Lewis Toyota it says this:



What came when I used that P/N is exactly what I was referring to in this post:

2x 90080-11420 Bolt with Washer
2x 90179-14063 Nut

 

This is why I don’t trust Toyota’s online parts system. My pics from the EPC show the part INDEX# is different but part number is identical. I’ve seen that semi-often in EPCs (electronic parts catalog - not referring to that website specifically). And it matches @des2mtn ’s reco too, unless I’m missing something.

 

https://youtu.be/9kVgwjeWXF4?si=UDPKdpnHEsI3tF_N

 

Never heard the original, so for me, this is the original now. It's not bad. Not an ICP fan in general. Had some Michigan buddies in college that loved those guys, way back when Bugz on my Nugz was their jam.

 

thank you very much for you help I think I’m just gonna go with the sequoia part and will see if it fits. My driver door is getting so bad I have to press the latch up with my finger so it can actually latch instead of slamming into the catch.

 

Thank you for your help as well, I’ve been having some frustrating experiences with the truck lately and this forum is a lot of help.

 

I ran home to pick up a package left on my doorstep by UPS. Got my new filter for Donut. With any luck(not gonna happen) I can get the slave and filter put in today.



Since I was already home and there's another foreskin on the job, therefore another work truck, I grabbed Ironman and drove him back. @FrenchToasty Tundra on call.

 

the BMF headlight special.


context: bmf drove around camp in sedona holding a flashlight out of his window because his headlights were dim & muddy.