WHAT HAVE YOU DONE TO YOUR 3RD GEN TUNDRA TODAY?

I just installed my Beat-Sonic PA2T3K. Nothing to it. Easy peazy. Sounds better for sure. I put gain at about 2/3 of the way up. I tested it before I put it back in. It appears that the rear gain control does nothing and the front one controls everything.

Question. I have a 1794. There was a wire and clip going into the back of the trim piece you take out above the glovebox. It was clipped in to nothing. It is not for the lights or anything, it goes to nothing, just clipped into blank plastic. Anyone know?

 

Yup. It's for the Capstone trim. It says "CAPSTONE" on their trim piece and it lights up. So, the connector goes to that LED that none of the other trim levels has.

 

Figured as much. Thanks!

 

I'm swapping the pipe back to original. The rubber hangers have stretched allowing the pipe to contact the step resulting in a OCD annoying rattle at idle. I'll update once I modify dual tailpipe by denting or cutting/TIG the contact area. bummer.

 

Installed new Husky X-ACT Contour floor mats. Loving them so far.

 

I can't tell from your photos, was your tail pipe chrome? I'm looking for the black chrome version.

 

Just did this yesterday, great mats and better than the oem Toyota all weather mats that come standard up here in Canada.

 

chrome tips

 

Don't do anything rash,I had the same problem with mine hitting/rubbing against the bed step and it drove me frigging nuts.
Loosen it just barely enough to twist the pipes to maneuver it,place it to where it needs to be and "overcompinsate" for the rubber hanger to do what it's going to do over time.

 

Tried that when installing. Will give it a go again over the weekend. May loosen the joint at muffler, throw a worm clamp on the tail hanger rubber to limit movement then bolt it again. Otherwise, out it comes to be welded.

 

Had her first good freeze

 

Good timing for my first fill up. Black Friday gas price deal at $1.00 off per gallon at my local regular station ($1.93 gal)!
First hand calculation came in at 16.44 MPG so will see how this goes after further break in.

 

Installed these

Muslogy Premium Custom Interior Non-Slip Anti Dust Cup Holder Inserts 30 Pcs Set Center Console Liner Door Pocket Liners Compatible with Tundra 2022-2024 (White)

$27 Muslogy fits Tundra Accessories 2022 2023 2024 Premium Custom Interior Non-Slip Anti Dust Cup Holder Inserts 30 Pcs Set Center Console Liner Door Pocket Liners Compatible with Tundra 2022-2024 (White)

https://www.amazon.com/dp/B0B7DNM1Y2

 

Getting 295/70-18 MT Baja Boss AT's fit on a bone stock 2023 SR5 SX +60 18X7.5" wheels at Discount Tire. They said they won't fit. Rolling the dice! LOL

Brad

EDIT - They fit!

 

Installed my Diamondback HD on my new 2024 Tundra TRD Pro in Terra color

 

Picked up a 75 gallon tank and stand.

 

I have these as well. Love the non-slip feature and feels.

 

It really was not very difficult. I actually used Patrick's video (right below your question) as a guide. I was by myself taking it off and it probably took me an hour or less to get it off and back on. Getting the winch plate installed and the winch mounted in the right spot took the most time (a few hours). I ended up having to drill extra holes because the holes on the CBI winch plate wouldn't work because of the placement of the fans.

All in all it really wasn't that bad.

 

Installed the Carven catback exhaust. It’s a little louder on start that I’d like but settles in once the engine warms up.

 

Ive run out of projects for now, and had a set of extra Baja Designs Squadrons in the garage. I finally found some use for them. Also threw some strut and LCA skids on from Victory 4x4


Now to figure out the next big project...

 

Sorry for dark pic, there was light out when I started . Installed rear cornfed 1” spacer. Fronts already had rough country M1 (at 1.75”) so it was front high

quick question, I had alignment done when the front m1 was installed last week. Does it need another alignment for rear spacer post install? Thanks

 

I’ve never touched alignment after a rear lift.

 

Solid axle so no need.

 

Did you install yet? How do you like it so far if you did? And photo is necessary.

 

Another great video by tinkers adventure about how our tundras suspension works.

 

Pics of the spacers and caliper covers?

 

Finally got my truck. Shout out Damian Lillard Toyota in McMinnville Oregon. The sales team basically did backflips to get my deal done on a Sunday afternoon. Guy beat me to the truck I was looking at so they sourced a dealer trade on a truck of my choice. Best service I’ve had in a long time. Stoked on the truck.

 

Oh ya, got those badges off her already.

 

No pics of spacers. Think I bought them off ebay and are 1.25". Worked out well.