WHAT HAVE YOU DONE TO YOUR 3RD GEN TUNDRA TODAY?

On my Limited I needed the Power package to get bed lights, 120V inverter and whatever else it included.

 

That explains it. I don't have the plug in the bed either so I guess that whole package is tied together. I do have the 2 usb plugs for back seat passengers but no 120V inverter in that spot either.

 

So, Toyota eliminated the TRD sport in '25 MYs? I have the convenience package in mine.

 

It's pretty simple to add your own bed lights, just takes time, & you can configure it however you want. This cost a total of about $30.

 

Looking good. I agree, the bed lights overall weren't that bad and much brighter than the ones that came with bed lights stock IMO.

 

Mine also has the 120v inverter.

As far as I know, there is no 25 TRD sport, yes.

 

Just finished blacking out and upgrading my center console. Love the dual wireless charger. So much better than the stock one.

 

Just starting with some small things, but got the bulletpoint mounting solutions kit installed and the Tufskinz door sill protection over the weekend.

 

You can go in your Toyota app under your truck>Info>Glovebox>Specs & Capabilities and it will show you all those add ons you have. My large tank is listed under the “Port or Factory Installed Equipment” header.

 

Small weekend project. Added the Rhino Rack 6 ski / 4 snowboard carrier to the areo crossbars for a little extra cargo management. Will be used for hauling fishing rods and kayak paddles. Just need to tweak the spacing

I look at those door sill protectors all of the time contemplating if I want to install them in the back for the kiddos. Looks good. Definitely going to have to do this.

 

Small weekend project. Added the Rhino Rack 6 ski / 4 snowboard carrier to the Areo crossbars for a little extra cargo management. Will be used for hauling fishing rods and kayak paddles. Just need to tweak the spacing a bit, and we're good to go.

 

I just did the front doors for now but I will add the back eventually. My son still needs to be picked up and put in his car seat so I’m not too worried about that for at least another couple years. It’s not too bad of a process, just gotta take your time and work top to bottom smoothing out the air bubbles. They are very easy to mess up if you get in a hurry with how sticky they are. They want to stretch some if you have to pull them back off to realign. But the fact I did it while my two year old was climbing all over me and the truck proves it’s not too bad

 

Mine should be here today! Thanks for the words of caution!

 

I would already have them if they didn't have that gay mountain scene on them.

 

I bought my '25 Limited TRD Off-road package with 3" lift just about a month ago. I immediately bought BFG TA KO3's in 285/60R20 and had the dealer install the TRD sway bar to make room for bigger tires.
This is my daily driver and I just want functionality for my lifestyle. I participate in competive shooting a lot. Probably 2 to 3 weekends of the month. Camp in the summer and transport stuff quite a bit as part of household chores as well as up to our cabin 3 hours north. I hunt every fall with a group of buddies and haul a bunch of coolers and camping equipment out to the lease and every thanksgiving drive back to my family's farm in the east coast to hunt whitetail.

My last Tundra had a cap and I loved it so I ordered an RSI Smart Cap EvoA and installed it by myself with a garage hoist.
My truck wasn't optioned with the power package so I installed some rock lights on magnets in the ceiling of the Smart Cap.Ordered some rare(apparently) molle backers for quickfists to store some tools on the doors of the Smart Cap and used M8 clamp screws to hang some traction boards. I also ordered a cheapo fire extinguisher and screwed some magnets to it's bracket to mount to the Smart Cap.
I ordered all the parts and pieces for the Heritage Pro grille swap and ahead of the install prepped the battery for multiple power accessories with a Blue Seas 6 gang fuse block and a 100amp circuit breaker. I bought some sheet steel and made a mount for the fuse box cover.
As I was finishing the wiring for the Diode Dynamics light bar in the Pro Grille I realized how nice it would be to have a dome light under the hood. I had one rock light left and ordered some more magnets but surprise!....the hood is aluminum, lol. So I copied @60centenergy and used a strip LED I had lying around. Last Friday RCI emailed the skid plate was ready so I drove up and picked it up and installed it at work. Super easy install and it looks great. I got aluminum for the weight savings and the fact that I'm not building a hard use 4 wheeler.
Next planned additions. I ordered a CAN M8 high beam switch and reader to link my light bar to the headlights. I also have two 30"L x 10" tall x 13" deep tool boxes that I'm going to mount to the bulkhead bed rail end to end. I'll probably have to build a little bench for them to sit in to bear the weight. Have at toolroll incoming and will pick up a Morrflate air compressor. I'll store the bottle jack, tools, air compressor, coveralls, snow chains, tire repair kit, jumper cables, tow strap, and hitch in those boxes. I plan on ordering a Backwoods Adventure front bumper and installing a 12K winch in the next couple of months. Lastly I plan on buying the Electrolatch auto locks for the Smart Cap to link to the doors lock/ unlock functionality. I think that will round the truck out and give me some preparedness and flexibility when dealing weather and conditions in the mountains.

 

You can get them in plain black now...

 

Sweet, thanks!

 

I mean, you can get them w/o the mountain scene.....

 

Nice work. Now you can see under that hood!

 

this looks awesome. Do you find they charge better than stock? Is thid from Slee or Beatsonic?

 

for all those gay mountain lovers

 

LOL

 

HAHAHAHAHAHAHA

 

Today I figured out the best use for the console cavity. Wireless chicken warmer

 

I'll bet it's much better at that than charging a phone!

 

New engine day!

https://www.instagram.com/reel/DH39uycSTs-/

 

I just found out that the AJT cupholder downgrade requires you to buy a part from Toyota as well. Adding that part in puts it at about $200. If you have to buy a part from Toyota, could you not just buy the whole thing from Toyota and switch it? Has anyone tried?

 

Truck looks badass…..

Factory lift? If so I have the exact truck in midnight black metallic.

Do 285/60R20 on the stock wheels give you any rub at all?

Thanks

 

Out with the old and in with the new