WHAT HAVE YOU DONE TO YOUR 3RD GEN TUNDRA TODAY?

I have the Toyo AT3 my 2nd set after running 4 sets of MTs my last set of MTs could not get them to stop pulling on my Tacoma. I run 37 psi all the way around

 

P/N is

$154 PTS3034000 PTS30-34000 Folding Truck Bedstep Compatible with Toyota Tundra(2022-2024), Retractable Rear Bumper Step, Easy-to-Install, Non-Slip, Corrosion-Resistant

PTS3034000. It's the manual OE bedstep from Toyota. I installed it on my truck and it's great. It does reduce departure angle slightly, but the trade off is worth it. IMO.

Pics of it on my build thread, if it helps.

 

Looks sweet! What did you wrap it in?

it is totally cemint hahah

 

Installed Air-Lift Ultimate 5000 air bags along with the Air-Lift WirelessONE air pump/controller. Installed an additional T at the passenger side rear airline and ran a manual fill valve to the receiver hitch mount where there is already a hole drilled. This will allow for manual fill in the event of a compressor failure, or if I need to reference the actual PSI for troubleshooting, using a physical gauge. It was quick and easy, and all the parts came with the kit, so figured why not. Compressor is mounted to the outside frame rail, just below the rear passenger door. I ran the fresh air intake for the compressor into the cab, as there is a wiring harness entry point in the same location that goes directly into the cab, and under the rear passenger storage compartment. Easy access with just a few clips to remove. All airline and wiring harness was put in a braided loom to prevent abrasion, although not necessary. Used a handful of extra 'christmas trees' to secure both the wiring loom and airline along their routes.

Also swapped the front grill surround with a color matched surround, and changed the TRD Off-Road grill insert for a TRD Pro grill insert. I've had a piece of window trim on back-order for two months now, but once that piece arrives, i'll swap out all 6 of them for a matte black window trim. I might try wrapping the door handles, but havent quite made up my mind there yet.. Slowly but surely, she's coming along!

 

Installed ********* cat shield today.

Take that you thieving bastards!




Next up Charvonia bed tie downs on Friday.

Then snow tires - Blizzaks on black alloy rims.

The truck investments continue…..

 

What the heck is up with this?? That bolt is way too long

 

Milwaukee leaf blower. I see you're a man that enjoys the finer things in life.

 

So not today, but Saturday I finally got to take the new truck home after they replaced the Passenger mirror damaged in transit. Loving this Truck so far!

 

Ah yes, it and the mower have exceeded my expectations and then some

 

Love it, looks incredible

 

I put on the Truxedo Sentry Ct tonneau cover, TVD decals on the rear, Go Rhino RB20 slims, and also upgraded to 285 75 18's. Love the new stance and no rub with the tires.

 

Installed 1.75" leveling kit.
Exactly level, maybe 1/4” lower in front at the most, depending on where and how I am parked. Will measure again on exactly flat surface.

 

Sorry to break it to ya but a 1.75 RC will give You a lean from the front being higher. Judging by the second pic yours is slightly higher in the front

 

Looks great

 

Rated for 300…I’m 230 and it’s solid as a rock…hope that helps!

It’s the OEM step…I saw someone already answered and gave the part number, let me know if I can help with anything else!

 

Sharp looking truck , like that color a lot.

 

No, it's not.
front is 1/4” lower

 

Okaaayyyy

 

Finally got around to installing the light bar today. Turned out great! Wish I had gone a little wider, but overall I'm happy with it, especially for the price. ($100 shipped). Has a 3 year warranty so I'll definitely get my money's worth at the least!

Install took me a few hours, but wasnt all that difficult. Drilled 2 holes straight through the crash bar and ran 4" bolts through them. Used one of the brackets that came with the light.

It's a Lasfit 22" Spot/Flood Combo

 

Looks great!

 

Installed tonneau cover. Access tonneau sport.

Then wash, decontamination, polish, and ceramic coat with Cquartz UK.

 

Ok, I am good and can follow all the way up to the installed tonneau cover part. I got a little lost after that.

 

Lol ok , plain english. Made paint look really good , then put a coating on it that lasts for a few years.

 

Got it yesterday. Scratched it today. Does that count???? ‍♂️‍♂️‍♂️

 

Today I brought the Tundra home. Still have a few minor details to wrap up next week but the first phase is done. Put the first 100 miles on it today.

 

nice
was it a hard install?

 

It's two bolts with spacers. Super simple.

 

Installed the Dongar Technologies dash cam adapter that plugs in to the OEM dash cam plug for USB power to aftermarket dash cams. It was a super simple install.

 

Installed Charvonia Design bed tie-down anchors from @602runner. The install was very easy.

 

Reached out to Rich @rrentrop with TVD vinyl and asked him for decals for the third brake light. He mentioned they were still in prototype phase and asked for some measurements, in return he sent me a set free of charge. I'd say the fitment is pretty spot on, I went the easy way out and did the dry application method and had some terrible lighting in the garage but overall I think they look nice. You'd have to be up close and personal to see any imperfection. Sent a ton of up close pictures to Rich and I. Sure he'll make the necessary adjustments and put out quality products just like always! Should be hitting his online store soon!