GEN 3 (2022+) Wheels and Tires Photo thread

Which one you think? 285/65/20 or 285/60/20?

 

Hey all. Trying to figure out which is the tallest safest size tire I can fit on my 22 Platinum stock wheels to fill up the wheel well? Trying to avoid rubbing, wheel poke and I probably will install mudflaps. I will probably go with the BFGoodrich KO2s because I like the look but I am stuck on which size to go with.

295/60/20
285/65/20
or
275/65/20

Any advice and/or pictures would be super helpful. Thank you.

 

35x11.5R20 fit great on the factory TRD wheels (I have a limited, so not 100% sure if the Platinum has the same wheels or?.... no level / lift, no poke, no rubbing, didn't have to pin the liner, and have mudflaps.... found this size cheaper than the metric equivalent as well. I had K02's on my last rig, and they got annoying loud after about 20k miles (similar size).. I went with the Nitto Recon Grapplers, and love them so far... only got about 3k miles on them... but so far so good... and I like the aggressive sidewall.. I have some pics if you click on my member name

 

Did you need hub rings for your rims? I have the same ones and patiently awaiting for my truck to arrive

 

Would the Falken Wildpeak LT295/70R18 fit on my Platinum factory wheels without any issue? What if I get a leveling kit for the front?

 

The Platinum wheels are 20", not 18", so those tires aren't the right size.

I have heard of folks installing 35" (or close) tires on stock Platinum wheels successfully with just a 2" front leveling kit. Without that you may have to do some trimming. I'm planning to use my stock Platinum wheels as well and just a front level to get close to 35" tires, like someone in this thread did: https://www.tundras.com/threads/35s-on-oem-rims.107959/#post-2826807

There are multiple posts in this thread about larger tires on factory Platinum wheels with just an Amazon front level and manual rear AVS adjustment, looks sharp: https://www.tundras.com/threads/leveling-22-platinum-with-avs-air.99893/page-2

 

Plenty of 2.5 gen people running 295/60s on the factory 20x8" wheels. Follow the above post too for good links. ^^

 

Thanks!

 

Hey guys! First of all, thanks to everyone that posted pictures of their wheels/tires setup, it helped me a lot to make my selection.

I went with Toyo Open Country AT3 275/70R18 with Fuel Rush 18x9 +20

 

Very nice truck . My new tundra will be picked up tomorrow after they put Toyo 295 60 R20 and ReadyLift 2,5 “ leveling kit

Enjoy

 

Out of curiosity what made you get that leveling kit vs a cheaper one on Amazon? I plan on getting a cheaper one, then the Toyo A/T III's 35/11.5/R20's. Also, if you don't mind me asking, what was the cost to get the leveling kit installed?

 

get the cheap level first to get the look and fit bigger wheels then once a full setup is readily available change it out. That’s what I’ve done and you don’t want to spend too much on a level just to pull it out.

 

Wait, so you got a 2.5" lift for both, or just a level? Isn't the level just 1.75" for the front?

 

2” level in the front, zero in the back right now. I want the TRD 3” lift and I’ll wait for that, the 3-1 westcott level is too much money to spend just to take it out later on. The 1.75” level is from RC, still too much money just to pull out again.

 

I thought you were the OP I had quoted, my bad. Yeah I am planning to get the cheap leveling kit and the 35/11.5/R20 Toyo A/T III's. Then if I ever decide to put a bigger lift on, I'll get something like the TRD Pro one.

 

They putting on tires and front leveling kit right now . Will pick up in few hours and send pics. I’ve been using ready lift on other tundras and been satisfied. Use trucks a lot on farm roads. Not sure how much installation is . I’ll let you know later today. Thanks

 

Sounds good! Hope everything goes smoothly.

 

Brought Pearl home today after adding Toyo AT 3 295 60R 20 and a ReadyLift 2” front leveling kit.

 

Finally someone with oem wheels with a nice set of tires thank you. So the 295’s do fit on the 20x8’s

 

I plan on getting a front leveling kit and the Toyo AT3's as well, but I was going to get them in 35/11.5/R20. Any reason you went with that size? From what I understand the 35's will fit just fine and will be a little bigger

 

Found out today and wanted to share that anything above a 2” leveling front kit , the front sensors would need to be calibrated. Could be bit pricey . My kit was 2” so I’m good.

 

Another Pic. Certain light has a silver metallic look and other light can look much more white

 

Little to large of a tire for my needs. Not sure how either will affect gas mileage. I’ll post something when I can .

 

Yes , the 35”s should fit good .

 

Westcott leveling kit
Method 316 18x9 +18
Nitto Terra Grappler 295/70r18

 

Any issues at all with these wheels? I’m about to order them as well.

 

No issues at all.
Good luck.

 

With my ReadyLift 2” front leveling, front is 39 1/4” and rear is 39 3/4” .

 

Already had them from my 19 build

No one has to my knowledge and my truck runs fine with 3in

love them, zero issues and get lots of compliments. Tuners think they are Volk te37’s

 

It’s the owners call as to get the sensors checked. Toyota will not do it . What I’m saying is that if an owner wants to be exact and match factory settings for safety etc , then they should get anything over 2” get alignment check .
Just saying….