1. Welcome to Tundras.com!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all Tundra discussion topics
    • Transfer over your build thread from a different forum to this one
    • Communicate privately with other Tundra owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

Subwoofer in an Access Cab... The Right Way

Discussion in '1st Gen Tundras (2000-2006)' started by 1stgenike, Nov 10, 2020.

  1. Nov 10, 2020 at 3:59 PM
    #1
    1stgenike

    1stgenike [OP] New Member

    Joined:
    Apr 16, 2020
    Member:
    #45119
    Messages:
    20
    Gender:
    Male
    Vehicle:
    '03 Tundra
    This is a quick little thread showing you how to fit a 10'' subwoofer under the rear seat of a 1st gen access cab. This has been done before but really hasn't been covered in detail.

    These trucks have no room whatsoever, so I had to get a little creative and throw it in the passenger side storage compartment, with the amp under the seat. This actually turned out pretty good, and sounds fantastic, but does get a tad annoying if you are constantly hauling more than 3 people around. If I could go back in time I would have just bought this. But if you are on a budget, the way I am about to explain is the way to go.

    Here's everything you need. A shallow mount sub and amp of your choice, 1/4" MDF, some wiring (copper if you want the best sound) and, most importantly, a decent amount of sound deadening mat. Generic works fine, here's where I got mine. Also going to need some stainless hardware, and some felt and spray adhesive, and fiber filling. I had an old amp laying around, and everything else cost me about $200.
    IMG_8551.HEIC.jpg

    IMG_8557 2.HEIC.jpg

    First step is to cut the MDF to the size of the storage compartment lid. Then cut the hole in for the sub. After you have the cuts and sized perfect, you can cover the MDF in felt or carpeting. I got mine from JoAnns. Also, if you want be a little bit extra, you can get some foam tape and put it around the bottom edge for a better seal.IMG_8553.HEIC.jpg
    IMG_8556 2.HEIC.jpg
    IMG_8564.HEIC.jpg

    Now here comes the hardest and most time consuming part. After pulling back the carpet, you will see that the "compartment" completely littered with holes. YOU HAVE TO COVER EVERY SINGLE ONE WITH THE SOUND TAPE IF YOU WANT THIS TO SOUND GOOD. There are gaps everywhere, even towards the back where you can't see. Use a pencil and poke around to find all the gaps. Fill them with the sound deadening tape. This is honestly the step that made me regret doing this whole thing. However, if you have the time, and have limited budget, this is still the way to go.
    IMG_8558 2.HEIC.jpg
    IMG_8559.HEIC.jpg IMG_8560 2.HEIC.jpg

    Now I ran my wires to the other side of the truck, because I only had a power cable long enough for the amp to be under the drivers side. You can really run it to either side, under the carpet, then under the plastic trim, and out to wherever it needs to go. There are countless videos on YouTube that can help teach you how to wire a sub and amp. Just give yourself a little slack.
    IMG_8567 3.HEIC.jpg

    Now you can start putting everything back together. Carpet gets tucked back in under the the floor trim, and then pack the compartment with fiber filling. The filling makes the subwoofer operate like it is in a larger enclosure. Connect your wires to the actual sub, and then use your hardware and screw down the MDF. You can use the existing holes, and drill a couple more if you want.
    IMG_8566 2.HEIC.jpg
    IMG_8568 3.HEIC.jpg

    Here's the final product. I ended up taking the grate off because it was digging into the seat when it was down. Now I just turn the sub off if I have people sitting on it. Turned out pretty decent, and the sound is great. Most importantly, it looks like it somewhat belongs there. No exposed wires or any other loose ends. This was my main concern when beginning this project, and is why I took the extra steps to make it come out better.

    IMG_8708 3.HEIC.jpg
    IMG_9390.HEIC.jpg
     
    Last edited: Nov 10, 2020
  2. Nov 10, 2020 at 4:25 PM
    #2
    FirstGenVol

    FirstGenVol Brake Czar

    Joined:
    Dec 13, 2018
    Member:
    #22934
    Messages:
    12,909
    East TN
    Vehicle:
    2002 AC
    Nice work. Thanks for taking the time to write this up.
     
    1stgenike[OP] likes this.
  3. Nov 10, 2020 at 5:10 PM
    #3
    shifty`

    shifty` The Second Shortcoming of Christ

    Joined:
    Jun 20, 2020
    Member:
    #48239
    Messages:
    19,079
    ATL
    Vehicle:
    '06 AC Limited V8/4WD
    (see signature for truck info)
    Good content. As someone who went with the Q-Logic dual 8 setup, some questions for you:

    As far as airspace goes, what is your actual vs. recommended on the sub?

    Is there a reason you didn't under-mount the sub on the bottom of the MDF so the cone has more cone travel ....

    Or any reason you didn't under-mount the baffle board inside the compartment vs. outside ...

    Or under-mount the baffle board and the sub for extra-extra throw and allow the seat fully down?

    I realize you're sacrificing airspace with any of these steps, but you can easily remove the metal cage, so bolting the baffle to the cage and/or under-mount would be no big deal if your 10" sub was made shallow-mount and-or shallow overall profile as-is.
     
    1stgenike[OP] likes this.
  4. Nov 10, 2020 at 6:33 PM
    #4
    1stgenike

    1stgenike [OP] New Member

    Joined:
    Apr 16, 2020
    Member:
    #45119
    Messages:
    20
    Gender:
    Male
    Vehicle:
    '03 Tundra
    It's hard to see in the pictures, but the bottom of the compartment is angled. I thought about mounting the sub or the wood under instead of over, but there is absolutely no room. Even with it mounted how I have it, the end of the sub is like 3mm from touching. As for airspace, I did this about 4 months ago, so I don't remember exact numbers, but the weird shape of the box made it hard to measure. I am pretty sure it was something close to .75cu ft. The sub states it needs 1.0-2.4 cu. ft. to operate properly. But even with the lacking space, it works just fine.
     
    shifty`[QUOTED] and Darkness like this.
  5. Nov 10, 2020 at 6:39 PM
    #5
    Darkness

    Darkness Allergic to white

    Joined:
    Jul 23, 2018
    Member:
    #17315
    Messages:
    9,976
    Gender:
    Male
    First Name:
    Luis
    All over SoCal
    Vehicle:
    The darkest
    It's really dark
    That's the hard part of putting a 10 in there. I've been eyeballing the Infinity shallow 10 and the JL shallow 10, they only need 3.25" depth I think, where the Polk is closer to 4.25"
     
    1stgenike[OP] likes this.
  6. Nov 10, 2020 at 7:10 PM
    #6
    shifty`

    shifty` The Second Shortcoming of Christ

    Joined:
    Jun 20, 2020
    Member:
    #48239
    Messages:
    19,079
    ATL
    Vehicle:
    '06 AC Limited V8/4WD
    (see signature for truck info)
    You can always add poly fill to disrupt the air behind the driver to simulate larger airspace for your sub. Cheap fix. More info from the most neutral voice I can find : https://www.crutchfield.com/S-Edxy5rMaZpV/learn/loudest-car-subwoofer-faq.html#14

    Also, something else you can consider, we used this to give a flush-mount appearance: Cut the hole in your baffle large enough the sub cage and mounting flange will slip through it Then cut an MDF "donut" with the inner diameter perfect to mount your sub, and outer lip large enough to glue it in and fasten to the underside of your baffle. This will buy you depth as thick as the MDF you chose, usually 1/2" - 7/8" depending on what you chose. You may not have much lip at the north and south.

    I went with two Kicker CompRT 43CWRT81 which require a little less than 2.75" depth. Sadly I looked at their 10 and it's looking like it's 3-7/16 mounting depth.

    I really think 8s are the sweet spot for access cabs. I'd prefer a single 10 or 12, but I'm not complaining with two DVC 8s. My HD900/5 arrived a few weeks ago and 4ga wiring supplies should be here in before December, hopefully I can finally get around to getting them wired up.
     
    1stgenike[QUOTED][OP] likes this.
  7. Nov 10, 2020 at 8:32 PM
    #7
    Darkness

    Darkness Allergic to white

    Joined:
    Jul 23, 2018
    Member:
    #17315
    Messages:
    9,976
    Gender:
    Male
    First Name:
    Luis
    All over SoCal
    Vehicle:
    The darkest
    It's really dark
    Not to thread jack but...
    Good choice, I have an RD 900/5 waiting to go in. Around the house stuff has been getting checked off little by little and that project might start in December as well if I can get my garage cleared out. Will be interesting to see different builds around two similar amps. I have some tricks up my sleeve for the sub.
    :fistbump:

    I ran a single 12 for over ten years and regretfully with age comes the "what the hell am I doing trading a seat for a sub box" question. Besides my wife doesn't let me bump so I pulled it out last year. :smack:
     
  8. Nov 11, 2020 at 5:19 AM
    #8
    bmf4069

    bmf4069 Yup, that's car parts in a dishwasher

    Joined:
    Sep 1, 2018
    Member:
    #18880
    Messages:
    7,273
    Gender:
    Male
    TX
    Vehicle:
    02 AC sr5 4wd v8
    :anonymous:
     
  9. Nov 11, 2020 at 1:56 PM
    #9
    Professional Hand Model

    Professional Hand Model A.K.A ‘Golden Hands’

    Joined:
    Apr 29, 2018
    Member:
    #14878
    Messages:
    15,007
    Gender:
    Male
    First Name:
    Fred
    ‘Somewhere’... a State of Mind
    Vehicle:
    2002 Tundra SR5 4WD 4.7L AC Silver Metallica
    Hand Protectors
    That one was a Hanging Curveball.
     
  10. Nov 11, 2020 at 2:08 PM
    #10
    shifty`

    shifty` The Second Shortcoming of Christ

    Joined:
    Jun 20, 2020
    Member:
    #48239
    Messages:
    19,079
    ATL
    Vehicle:
    '06 AC Limited V8/4WD
    (see signature for truck info)
    Pulling out isn't a viable solution for ... wait, what were we talking about? :bananadance:

    Ultimately, space being a premium is why I ended up with this 8" amplified MTX that I never ended up installing in my Camry. Despite being brand new/unused, I can't even sell for 1/4 what I paid for it, it's sad, this specific unit kicks. Sad times. But I sold off my older (but near-mint) JL amps to bmf and an old PG power grid that netted half what I needed for the new HD900/5. I'm in the same boat with house stuff; I'm hoping to start my install by mid-ish December. I think I'm installing the amp under the passenger seat, I need to think through how I'm going to mount it. Maybe I'll come back to this thread later and post mine to show other options.
     
    bmf4069 and Darkness[QUOTED] like this.
  11. Nov 11, 2020 at 6:17 PM
    #11
    robabeatle

    robabeatle New Member

    Joined:
    Jun 14, 2020
    Member:
    #47947
    Messages:
    826
    Gender:
    Male
    AZ
    Vehicle:
    2002 Tundra 4x4 LTD AC
    Bilstein 6112 & 5160, Katskinz, audio upgrades
    I went with the Q logic and Alpine drivers. Really feel like this is plenty for most music. I made a grill that is not in the picture below but is just a piece of wood that goes across and allows someone to sit in the seat and not dig into the cone.

     
  12. Mar 21, 2021 at 9:40 AM
    #12
    bokch0y

    bokch0y I'm a sucker for DirtySOHC's

    Joined:
    Jul 1, 2020
    Member:
    #48708
    Messages:
    71
    Gender:
    Male
    I am looking into this type of set up as well. Did you have to do any cutting or trimming to get this to fit or is it essentially plug play right into that storage area? Thanks.
     
  13. Mar 27, 2021 at 5:20 PM
    #13
    robabeatle

    robabeatle New Member

    Joined:
    Jun 14, 2020
    Member:
    #47947
    Messages:
    826
    Gender:
    Male
    AZ
    Vehicle:
    2002 Tundra 4x4 LTD AC
    Bilstein 6112 & 5160, Katskinz, audio upgrades
    Basically plug and play other than some carpet slicing to get it to fit. I am very happy with the setup. I also added a wooden brace across the top of the sub because when a passenger sits in the rear seat it sags enough to hit the sub. I could not find any premade covers that worked so just some scrap wood did the trick.
     
    bokch0y[QUOTED] and two2cal like this.
  14. Mar 27, 2021 at 6:44 PM
    #14
    Jack McCarthy

    Jack McCarthy Truck repair enthusiast; Rust Aficionado

    Joined:
    Nov 2, 2020
    Member:
    #54409
    Messages:
    7,727
    Gender:
    Male
    First Name:
    Bill
    North of Boston
    Vehicle:
    02 Tundra AC SR5 V8 4x4
    Interesting. Last time I tried to build an MDF box and fitted it inside instead of using fiber filling. It worked but I got a bad vibration when I turned it up, so I returned the 10" JBL sub and tossed the box I made.

    Never revisited it since with tinnitus my ear can't stand even moderate levels of low bass for a long time. Although it was fun to pulling up next to a ricer with a wing in the back at a light and blare the opening to "Enter Sandman" where you got the full effect of the bass. :headbang:
     
    Darkness likes this.
  15. Apr 7, 2021 at 2:10 PM
    #15
    bokch0y

    bokch0y I'm a sucker for DirtySOHC's

    Joined:
    Jul 1, 2020
    Member:
    #48708
    Messages:
    71
    Gender:
    Male
    I ended up going with pretty much same setup as @1stgenike utilizing a 10" JBL. Sounds pretty good and zero rattle on my truck though I didn't do the sound matting but i also don't have it cranked as I'm not 20 anymore haha.

    The grill - i am also looking at that grill but specs indicate it's about 1 5/8" in height? Does that sound right? I'm thinking this is too high as the sub itself is already higher than the original cover. Are there any other recommendations for a grill?

    Thanks.
     
    1stgenike[OP] and Darkness like this.
  16. Apr 10, 2021 at 10:40 AM
    #16
    1stgenike

    1stgenike [OP] New Member

    Joined:
    Apr 16, 2020
    Member:
    #45119
    Messages:
    20
    Gender:
    Male
    Vehicle:
    '03 Tundra
    I actually ended up just taking the grill off because it was definitely too tall. It really dug into the seat when it was down, so now I just turn the sub whenever I put the seat down.

    What I thought would be the best plan would be to build something like this, that goes over the entire sub area and fits the seat bottom when placed down. The seat will not lock in the down position with this idea, and it will sit about an inch higher than the single jump seat when both are down.
    image0-1.jpg

    Basically two 1/2 inch thick triangle supports spread as far as possible, with angles that allow a sheet of 1/2 wood to be placed on top and not hit any park of the sub. Add some carpeting to make it fit in. (Also I spelt towards wrong lol)

    I figured this would be the answer to the sub still working best while the seat is down, and allow the seat to have a full platform to lay on so the leather isn't creased. I rarely have more than 2 passengers in my car, and I went back off to school, so never had time to actually make this, but I don't see why it wouldn't work.
     
    Last edited: Apr 10, 2021
    bokch0y[QUOTED] likes this.
  17. Apr 19, 2021 at 7:12 PM
    #17
    bokch0y

    bokch0y I'm a sucker for DirtySOHC's

    Joined:
    Jul 1, 2020
    Member:
    #48708
    Messages:
    71
    Gender:
    Male
    Great idea and thanks for that. I thought of something like that as well but I was more going to just cut out a template similar to the subwoofer template but with a larger opening and then getting one of those flatter grills for protection. Guess it's another project...
     
    1stgenike[QUOTED][OP] likes this.
  18. Oct 8, 2021 at 9:15 PM
    #18
    Jdtuned

    Jdtuned New Member

    Joined:
    Jun 7, 2021
    Member:
    #64022
    Messages:
    27
    Gender:
    Male
    First Name:
    Jorge
    SoCal Whittier
    Vehicle:
    01 AC sr5 4.7 2wd
    No mods besides regular maintance and up keep. Required to carry 200lbs of tools for work.
    How is the sound with the seat down? Does that hinder the performance of the sub? What if you have a gap between the seat and the sub? I figure if you have an air gap then the sub should work as intended with no issues. I was thinking you can mount the wood inside the enclosure and mount with some T-nuts and spacers to lower the sub further into the enclosure. By doing so the seat wouldn’t touch the sub. Does this math make sense? I don’t know please correct me if I am wrong.
     
  19. Oct 8, 2021 at 10:19 PM
    #19
    KK6PD

    KK6PD 2 1 yr. retired . . . after 42 yrs

    Joined:
    May 25, 2021
    Member:
    #63524
    Messages:
    321
    Gender:
    Male
    First Name:
    ROAD
    Upper Los Angeles Foothills
    Vehicle:
    2003 AC Tundra . . . . 7th owner
    New Tires, Stereo & Speakers,Uni-Strut Tie Down Continue watching THIS SPACE FOR FUTURE DEVELOPMENTS
    What a great idea and project write up. You do good work, and the write up shows it!
    Having just redone my audiosystem on my AC, I can appreciate the work you have done!
    Thank for your post!
     
    1stgenike[OP] and Tundra2 like this.
  20. Nov 14, 2022 at 12:13 PM
    #20
    Rcdlifttundra

    Rcdlifttundra New Member

    Joined:
    Apr 21, 2022
    Member:
    #77442
    Messages:
    22
    Gender:
    Male
    First Name:
    Grant
    Vehicle:
    2002 Toyota Tundra
    6 inch RCD lift 35x12.50x17 Tire swing gate tailgate delete 4.56 gears JBA headers Magnaflow exhaust
     
  21. Nov 20, 2022 at 6:00 AM
    #21
    robabeatle

    robabeatle New Member

    Joined:
    Jun 14, 2020
    Member:
    #47947
    Messages:
    826
    Gender:
    Male
    AZ
    Vehicle:
    2002 Tundra 4x4 LTD AC
    Bilstein 6112 & 5160, Katskinz, audio upgrades
    I believe they are called type R. I recently replaced the 6.5s with new stereo integrity 6.5s which match my SI tweeters. I spent about 3 hours giving the DSP a tune yesterday and this system rocks!
     

Products Discussed in

To Top