WHAT HAVE YOU DONE TO YOUR 3RD GEN TUNDRA TODAY?

37X12.5R-17 Cooper Discoverer AT3 XLTs wrapped around Motegi MR150 Traillights (17X8.5 6X5.5)

 

Slapped on the new TOYOTA center caps. Didn't have to remove the wheels, just used a small pick and pried them off

 

I ordered the bronze Toyota centre caps for mine but Canada post is an absolute disaster. Last and only update was they picked up my parcel from shop January 7.

 

Found a new trd skid plate for half off. Install wasn’t bad except for the pita air dam, other than that took about 15 mins.

 

Been waiting for a sub $300 deal around here but most go for 350+

 

What did you use to mount the holster

 

Looks great. Any side profile shots?

 

3d scanning some interior parts to design my own cupgrip thingy (couldn't be bothered to take my emergency fruit snacks out of the console area)

 

What scanner do you use?

 

Just curious: did you move it from the driver’s side to the passenger’s side? Or do you now have two? If you have two, what’s the purpose…just to make it easier to get to?

 

Borrowing one of my coworkers’ Shining3D Einstar. It wasn’t the best at picking up black plastic so I had to put a bunch of baby powder on the pieces that I was scanning.

I cleaned the baby powder off this piece of trim before taking the pic, but it did a pretty good job! Gonna use this piece of trim to make a flush mount for my auxbeam. I’ll post an update and .3mf files once I process the scans and design some parts. Also took a scan of the front cup holders on my mom’s 3rd gen limited sequoia that has the vertical cup holders/lil cover - I believe that’s on the higher trims of the tundra.

 

sent you a private message !

 

Despite it being bitterly cold in Kentucky, I’ve been dying to wire up the marker lights in my grille. I did the heritage grille swap with the factory TRD marker lights a few weeks ago but didn’t wire the lights up because they didn’t have a wire harness with them. After reading, I decided to knock it out really fast and I’m pumped!

 

Installed the Yota Xpedition Pro Grille with topo letters as well as their vent lights. Light bar switch was on backorder, so I still have to wire that up once it comes in.

 

Got some goodies installed. ARB dual compressor, Blaze Offroad Rear Power Kit, Garmin Powerswitch, SDHQ Under Hood Power Solution Kit, C4 Lo Pro Bumper, Warn Zeon 12S Winch and a bunch of Baja Designs Lights. Next things to be installed will be roof rack with Baja Designs LP6's. Install by @boatzNhoez

 

Quick mockup to test if the scan was scaled properly, and it was! eyeballed the orientation so it’s a lil tilted but I kinda like it

 

I bought another switch and black plastic fairing for it, I did it to make it easier. Wish I could do what the 25's had for the tail gate to raise without manually doing it.

 

Despite the cold and snow here in Kentucky I decided I was gonna put on my Rhino Rack Vortex Bars.

 

Shoutout to @Bnewman077 and OC Tire N Auto in Fullerton, CA. for taking care of me. Installed the leveling kit, Icon Recon SLX and new 35” tires today! Truck looks gorgeous!

 

which are you trying to do ? I have scanned and created STL's for almost everything in the front of the truck. ( just finished a custom camera mount for rear window (trucks with the slider window)

Would enjoy seeing what your doing as well....

 

First time she's seen snow

 

Thanks RC for stickering the hell out of the fender liners. Damn it

 

WD-40 is your friend

 

Steam too

 

Mine were on the back side, but I still removed them all

 

Nice! Was mostly trying to get a scan of the trim to the left of the steering wheel to make a flush mount for my auxbeam switch. Also wanted to get some of the cupholder geometry to design my own cupgrip-adjacent thingy. Was going to take off the front bumper to scan mounting points on the frame just in case I wanted to make my own front bumper but I think I’ll end up buying this one when I have some extra cash: https://outgearsolutions.com/products/2022-toyota-tundra-prelander
I’m going to add to my 3d printing thread with my files once I get some time to process the scans and design some parts. Would love to know what you’ve scanned and what you’re doing with those scans!

 

3d print folks - how about printing a hard frame for the cabin filter that would allow use of generic hvac filter material?

 

Takes like 3 seconds to peel them off.

 

Let me know specifics and I can do it...

 

This is a good idea, I like it.