What have you done to your 2.5 gen Tundra today?

Started the install of the circuit breaker, fuse block, and mounting plate.

 

My cars always require a blood sacrifice. This is the way.

 

Ask and you shall receive. These just adhere in place (I believe you remove the red letters and these go in their depression). You could also just paint your existing letters.

https://www.tufskinz.com/collection...id-plate-toyota-tundra?variant=32945811816544

 

Got the RCI trans skid and cat guards in place for some piece of mind.

 

OEM LED FOG CHROME: PT413-42190

OEM LED FOG BLACK: PT413-42191

 

I won't even tell you what I did to on my 2013 that gave me permanent scars. It bled for almost 2 hours before it stopped......I don't like doctors so,I stayed away from them lol.

 

My personal best, was welding metal in the garage, had a lot of slag...decided I'd just keep my welding helmet on while I grind it down with an 8" industrial grinder I have...I'm wailing on it, start wondering why it's so hot...pull up my visor, and the sparks I'd thrown had set my flannel shirt on fire! Used my welding gloves to put myself out, no harm done...flannel shirt total loss.

 

As far as what I did on the Tundra, aired up the tire! I've developed a slow leak (two days and the light comes on) over the last few days. Factory original Michelins, 58k, so about that time. I just put a deposit on the new Nokian Outposts, should arrive 7-10 days, so I'll just nurse it, keep an eye on it till then. If it worsens, I'll throw on the spare. Sigh...

 

Nailed it.

 

This sounds good

 

So it was a project on my 2013. I removed the coin holder on the dash to make a switch mount. It was posted somewhere that the metal disc handles from sliding closet doors fit perfectly in that spot. So off to Lowes I went, and bought a pack of metal handles. I drilled 2 holes to mount switches. I needed them a little bigger, so I busted out the step up drill bit. Like a dumbass, I was holding the disc in my hand...kind of like giving someone the okay symbol. The step up bit caught, and spun the disc in my hand. Imagine how sharp the edges are on those handles. I wrapped my fingers in wet paper towels and it finally stopped bleeding after about 2 hours. I have scars that look like shark bites....that's what I tell kids when they ask lol.

 

Classic!

 

Just got a chance to snap a picture. Within the last week I’ve got
Tint- 15% all doors and back glass, 50% windshield with 5% brow.
Rough Country 2” leveling struts
OCD Console organizer from Amazon

now to figure out if I want to debadge or not….

 

Hows the ride after the suspension upgrade?

 

If there’s a difference from stock, I’m not sensitive enough to tell it.

 

both got baths. 4runner got cut, polished, and waxed

 

Looks good!! What products did you use?

 

Good looking Barcelona Red. They sure clean up nice.

 

Chicks dig scars

 

How's the 15% at night?

 

It’s fine for me. But I’ve had multiple with 5%. I don’t notice too much difference at night between the 15% on this truck and the 25% on my work truck

 

looking to get 50% on my wife's Durango. can you post a picture from the front and how is it at night ? its ceramic tint by the way

 

When I got in the truck during the day (4pm ish) the day I got it, I almost went back inside and told them I wanted the windshield done. It’s not much different at all on the inside except my eyes hurt a lot less. I’ve got enlarged optic nerves and blue eyes so UV hits me double hard. Here’s an outside day time pic. I’ll take some from inside next chance I get.

 

My windshield is 50%.