What have you done to your 2.5 gen Tundra today?

Yup 5x150, don’t know what finish I’ll go with yet

 

You will have to tap into the wires but they are at the connector. I did it with my Muth signal mirrors on my 2020 SR5.

 

37x12.50r17. Discount tire direct had 6 in stock. I’ve been checking every few days for the last couple weeks. Originally looked at bfgs since I knew Mickeys were hard to find until they popped up today. Shipped out today should be at my house Thursday.

 

They’ll design anything needed.

 

Got a link for where to get these???

 

I got the turn signal version

https://spottermirror.com/make/toyota/tundra/

yes

 

Those look good. How was the install? Easy as the video makes it look?

 

It’s not hard but not as easy as the video. Getting them to pop out was a little difficult but they will pop out. Just don’t hulk it and break anything. I didn’t but can definitely see someone prying too hard or at a bad angle and breaking the lens

 

Good to know, thank you. What tool did you use for the removal and install?

 

The truck came out of New York according to Carfax and it had less than 18,000 miles on it when I bought it last summer. The pins had a ton of rust on them and wouldn't let the pads slide freely. I looked at the rotors and old pads. They were in pretty bad shape. I think it had been driven in the snow and salt, then left to sit.

But it doesn't matter now, cause its got new pads and rotors all around. Plus I trust the shop. Been dealing with them for years.

 

Just some pry tools

 

You indicated the truck was pre-wired for turn signals. Did your truck originally have turn signals in the mirrors? Just checking. Thanks,

 

Truck did not come with turn signal mirrors of any kind. It is wired for turn signals

 

So just to be clear, if you get the turn signal version (Spotter+heat+turn signal) you can just tap into the existing wire plug to run the turn signals even if you DID NOT have turn signals already. That sounds great.


Also just talked to the owner (Spas) and he indicated that due to real estate on the mirror it would be very difficult to put the BSM+Turn+Spotter+Heat all on the mirror so he is NOT considering creating that version at this time.

Looks like this could be a FatherDay's gift from the wife.....

 

Yup, that's it.

You will have to remove the entire mirror assembly to run the wires, unless you are talented and can do it with them still on..

 

Installed EBC rotors and Green Stuff pads on the front. Getting ready for my cross country drive back out to California.

 

Received my coach builder order. These shackles are seriously no joke!
2” shackles
Bumper spacers
Strut shims
Diff drop
Carrier bearing drop
Abs relocation brackets
Bump stop extension

5100’s, coach builder, Relations Race wheels, and my 35’s are all ready to get installed. Can’t wait

 

Hell yes!!!

 

Thinking about ordering some flag magnets for the side of my Tundra. I keep seeing ads for Tactilian on my Instagram feed but they are significantly more expensive than the other options on Amazon. Anyone have any opinions on if Tactilian is worth the extra money?

 

i've had them for a bit. i like that there's not any dirt that gets into the cracks/crevices "semi-permanently". you take it off to wash the vehicle (at least I do anyway), then put it back on. i'm happy with them!

 

The last time I checked, the US flag had 50 stars!

 

Then get ready for an "affliction style" d-bag sized flag magnet to be able to put every single star cutout in there.

 

Doesn't the Amazon example shown have 50 stars?

 

i remember talking with someone and/or reading reviews of one that had all 50 stars cut out. they said it looked bad and the magnet was thin/cheaper quality (hence price difference)

 

That truck is so killer. Lunar rock color match & black looks so good together. I thought the desert sand/tan would be tough to top but this clears it easy.

 

each color has it's pros and cons. except white

 

Exactly right.. no cons with the white

 

Removed the tundra and limited badges....Used dental floss (thick rope looking stuff) and sawed through the badges like on you tube, then goo be gone with my finger tips an nails very gently....Then some cleaning wax (and raw finger tips)...then washed the whole truck.