What have you done to your 2.5 gen Tundra today?

How much if you dont mind sharing.

 

Hey thanks!

 

Including windshield and front window tinting, $4k. They didn't/wouldn't do the inside door jambs or completely behind the cab (they would need to remove the bed) but I'm okay with it.

 

Recently upgraded suspension and a few other goodies(pics to come). OME Nitrocharger w/dakar leaf+Add a leaf. Method 703 with Cooper STT Pro. Skids, Air compressor, fridge wiring, etc. Next up: sliders and bumpers.

 

I bought it from a nearby (83 miles away), Toyota dealer from Toyota.com. Paid $400 for it.

 

What tranny cooler kit is that?

 

Nice
How much does that stuff cost?

 

$150 U-POL Raptor Black Urethane Spray-On Truck Bed Liner Kit W/Free Spray Gun, 4 Quarts

https://www.amazon.com/dp/B01CKE7B1E/?coliid=I31DW04ECV1UOP&colid=EE42AJHADBEF&ref_=lv_ov_lig_dp_it

 

You can get Raptor liner in an aerosol can at AutoZone.

 

Right on
I might get a can and play around with it to see if I can pull that off.

 

Its not that expensive.

Make sure you have a decent compressor to apply the product if you want the rough texture.

The areosol cans are good for touch up areas, but dont give the same results as with a compressor and the liner and hardener mixture.

Just my $.02

 

Thanks.
You answered my questions without me even having to ask them.

 

Where did you get those racks?, all 4 of them?

I need them for my Kayaks, and my other boats and boards.

Thanks

 

It was a kit offered from this guy and he just stopped offering it with this specific cooler.

https://www.tundras.com/threads/tun...ne-cooling-systems.60550/page-40#post-2504526

 

do you use a heat gun to debadged?

 

That looks good. What was the cost?

 

Had one of my nitto ridge grapplers refuse to balance a few weeks ago, got the replacement in and getting it balanced currently. Looking at red lobster through the window...

 

Yes just make sure you clean pillar good, add adhesions promotor and be very careful when install the carbon fiber overlays

 

Yakima HD overhaul racks, they are very popular now seen more and more truck using them…go to Yakima.com

 

New surround and hood bulge... actually fine with the limited grill

 

This looks great!! Can you post links to the parts and some tips on install?

 

Hood bulge is a few 10mm screws and then pressure clips. Once screws are out, slowly tug and remove the hood bulge.
For 2018 and up, unplug the TSS sensor. Grille has 4 10mm screws and a few button clips. Onces those are removed you reach down into the engine bay and push the guide clips free (1 on each side and an arm length down and each end) once the grille is loose, just tug to put each side free (can do solo or have someone help).
If you are removing the insert from surround, ensure clips are warm (cold plastic breaks easy) and slowly pop them free. You will probably break a few but it should affect it too much. There are also some screws holding the insert to the surround.

Edit: thanks @Tundra234. Added unplugging TSS sensor.

 

SICK! What did that set you back? I was debating on doing the mat wrap. Is that a color match mat wrap or the mat clear film?

 

Don't forget to unplug the TSS sensors on the 2018 and up before you yank the grill off.

 

$419 shipped from Sparks got the 2014-2017 platinum grill was $100 cheaper than current model... bulge about $195 free shipping. The hardest part was removing the grill insert from new grill... used heat gun for a few secs on clips and then nylon pry tool. Only broke one clip....

Have some SCS rays and Eibach 2.0 kit to do next... and find tires.

 

I did get some wrap samples recently and the 3M 1080 Gloss white aluminum? Seems to be pretty damn close to match. I may do that to bumper ends... or go matte black on those.

 

That looks awesome! Making me think of pulling my Trd pro insert and putting my limited one in

 

You got the whole truck wrapped? What does that run?

 

See the post at the top of page 2203 from the guy that got it wrapped. You quoted somebody that was commenting on it.

 

Got the BMC today here in South Texas, and ordered some Nitro gears.