What have you done to your 2.5 gen Tundra today?

Depends on the car wash - I use the one at Bucees here in Texas and have plenty of room - even with the mirrors in they operational position..So again its gonna depend on the car wash!

 

I did notice when it started the arms moved in and out, maybe it was scanning me and then moving close for optimum distance

 

You don't neccessarily run into crocodilians at the beach... I have never heard of one at the beach... But there are sharks...and the water is warm enough to swim in.

 

Haven’t done it yet, but these arrived today and are a good glimpse into my future…I’ll post up before and afters of course!

 

Fuhking sexy!
I didn’t know Red was an option!

 

I was thinking the same thing!

 

I didn’t either until David called me on Wednesday saying I’m getting the first set from the production run in red, if I wanted them…unless I wanted black instead. I was all…pfft! RED please!

 

That's awesome. Same price as the black?

 

Same price, twice as sexy!

 

Make sure your ABS wire has enough slack in it. I had to bend the bracket a little when I installed mine...same setup.

 

The line-x will look good to blend with the center bumper fascia.

 

The chrome gets scuffed and the entire piece gets encapsulated in the line-x.

 

Installed my USB retention cable, wired my Muth turn signal mirrors, and rewired my reverse trigger wire on my Anytime Backup camera kit.

 

Installed the @Diode Dynamics 30" stealth lightbar. I will say the light output is out of this world. However the brackets leave something to be desired. My bar shakes while at speed. Not so much a fan of that but I will try to figure something out for that.

Side note if you need something for your truck, I CANNOT recommend @memario1214 with hotshot offroad ENOUGH. This man has my business for life. He really took care of me.

 

Dam that sucks that it shakes! I’d be pissed spending that much and having that happen! Kinda glad I went with rough country’s 30” was $250 and doesn’t shake a bit…maybe you can buy there brackets for yours and fix that?

 

Yeah that's probably what I'm going to look into is another bracket option. The bar itself is worth the price. It's extremely good quality.

 

Seemed to be okay when it was on the lift. I removed both screws when installing and they seemed to go back in with out any issues but now you have me worried

 

for what it’s worth, after I bought my 42” DD lightbar it shook a lot after taking it in the dirt. Took the setup back out, put bigger washers on and retightened and it’s been good so far.

@memario1214 was a great rep to deal with. Customer service was awesome.

 

Please tell me you don’t drive around the streets with all of that on. I get it if you’re off-road but outside of that…

 

It's not a big deal to adjust if needed and it's easy to tell if you need to. Every truck is different. The slack in mine was tight once the bolts were in. All I had to do was twist the bracket with a pair of needle nose. I will take a pic of mine in the morning.

 

Yep, crowded streets and residential neighborhoods, just like that.

Obviously not. Light bar is for empty backroads or offroad use.

 

Can always paint them for 10 bucks

 

Agree on Hotshot... Awesome Customer Service before and after the sale...

 

yep same here…I run all my sheeet all the time…Fuggum!

 

Finally got my 6112 coilovers and JBA UCAs installed after sitting in the box for over a year.

 

Yes. You’re absolutely right. I fixed the bracket just a few minutes after posting this photo. Good eye though!

 

You sure its vibrating on the bracket and not flickering?

I think mine flickers due to dirty power from the truck and plan to install one of their anti flicker modules in line.

If its actually bouncing it might be easier to support it with with something between the light bar and the solid bumper below it.

 

I take my crewmax thru the beaches carwash on beach blvd near hodges. Never had an issue and I dont fold in mirrors.

 

Yeah it's vibrating. I ordered Cali raised brackets as it supports below and above the bar. If those won't work because they're made for a 32" instead of the Diode 31" bar, I will chop them and modify them to make something work.