Wanting to run 35" tires????

Mine has a 3.5” lift and on 35x12.5x18 no issues at all. Front bumper helps though. I’ll be stepping to to 37s next tire- if not 38s

 

I’m running 35x12.50 toyos on a 4.5” BDS suspension lift on 20x10 wheels. No rubbing at full lock, had to trim little plastic and take off front flaps.

 

I’m running 35x12.50 toyos on a 4.5” BDS suspension lift on 20x10 wheels. No rubbing at full lock, had to trim little plastic and take off front flaps

 

Running a 35x12.5x18 on 18x9 +25 Ray 10s with just a leveling kit. I had to trim skid plate and do some front liner work.
No rubbing at full turn.

 

Thanks guys, finally pulled the trigger and this is where it's at now! Pic was taken months ago btw

 

I'm running 5100's on the front on the top setting and 5100s on the rear with no lift... 35x12.50R20 Nitto Ridge Grapplers... but I had to cut the skid plate, do the body/cab mount chop, .5" front bumper shims, and use wheel spacers...

 

Good to see that you got those xmas lights up early this year!!

 

Thanks guys, finally pulled the trigger and this is where it's at now

I took them off after I realized it was like February...I got the truck done in January lol

 

So what did you end up with?.wheels/ tire/ lift?

 

I went with a 5" Zone Off-Road lift, 35x12.5 Falken Wildpeaks AT's, 18x10 Moto Metal -18 Offset

 

You guys have your tire sizes way off a 285 is not a 35" tire. To run a 35" tire you need at least 3" and a body mount chop

 

5100's up front on the top setting, 5100s on the rear, no other lift. Cut the skid plate and did the body/cab mount chop. Stock wheels with wheel spacers and .5" front bumper shims... 35x12.50R20 Nitto Ridge Grapplers.

 

I put 20x9 rims with 1 offset and 35x12.5 km3’s. Rim place said I would have no issues with my ready lift 4/2” leveling kit. Im at the truck shop now getting the frame ground down and the front of the wheel well. Not even close to fitting. This was the last thing I wanted to do, but too much in to turn back now. ​

 

2018 SR5 CM leveled with 35x12.5 on stock 18x8 wheels. NO BMC. Just had to trim a little plastic in the wheel liner

 

I know this is an old post, but what rims were you running? I have stock TSS Offroad rims (2017 year) and am wondering if this setup would work for me… Not sure if the offset is enough.

 

Not sure what kind of lift / level you have, but you can fit 35’s no problem

 

Looks great mate! Did you have to run wheel spacers with those stock wheels? I'm looking to go with the same tire size after lifting my 2020 CM.

 

Needing to do this on my 18...Have about 10 k left on tires but just took out a nice chunk in my sidewall...time to get tires.Please details as to lift and tires ....Thanks

 

3" isn't needed. I just did Fox 2.0s @ 2", 2.0s in the rear with no block or shackle. I did do a BMC but 35s fit just fine.

 

Nice looking truck.

 

I know it's an old thread but I'm installing the 6112 Bilstein coils with a 2.5" lift. Could I run 35"x12.5" tires on the stock 18" rims with 60mm offset??

 

35 x 12.5 on 17" racelines +0 offset, cab mount chop and light bumper trimming but I don't rub at all on road or off-road.