1. Welcome to Tundras.com!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all Tundra discussion topics
    • Transfer over your build thread from a different forum to this one
    • Communicate privately with other Tundra owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

Rear Bumper lower bolt size

Discussion in '2.5 Gen Tundras (2014-2021)' started by Ryooo, Apr 3, 2020.

  1. Apr 3, 2020 at 4:27 AM
    #1
    Ryooo

    Ryooo [OP] New Member

    Joined:
    Jun 14, 2018
    Member:
    #16132
    Messages:
    113
    Gender:
    Male
    Boynton Beach FL
    Vehicle:
    2014 CM SC Platinum
    TRD Supercharger 4.5 BDS lift 20” Method Standards sitting on 35 Nitto Grapplers Rigid grill top and bottom with lights AMP running boards Fender flares Magnum rear bumper Rear LED bar Air bags with onboard compressor Brake controller Alpine Navi Alpine amps x 2 Focal Separates front and rear 2 x JL 13s in a stealth box behind the back seat LTE cellular booster Rear seat under locked storage Dynamat from ceiling to floor LEDs all over Bed liner Bed rails Paint protector covering nearly the entire front end and more
    Hey looking for some help here.

    I have a 2014 platinum crewcab. I have an aftermarket rear bumper, a Magnum, that was installed by the previous owner.

    for one reason or another the bolts that hold the bumper to the lower part of the frame are not there.

    The holes in the frame have a nut welded on the upper side as to make it so you can just thread the bolt up and in.

    Does anyone know what size and threads this nut? Hoping not to play a game of find the correct bolt.

    thank you
     
  2. Apr 3, 2020 at 4:41 AM
    #2
    Tundra2

    Tundra2 Zoinked

    Joined:
    Feb 10, 2019
    Member:
    #25875
    Messages:
    6,794
    Gender:
    Male
    First Name:
    Noah
    Western Kentucky
    Vehicle:
    '02 Tundra V6 SR5 '08 Sequoia V8 SR5
    Deer guard, LED everything.
    If you tinker a lot I would invest in a thread checker.
    Nut & Bolt Thread Checker (Inch & Metric)
    https://www.amazon.com/dp/B003FJW0GK/ref=cm_sw_r_other_apa_i_BcYHEbXGGFWPK

    If you don't tinker a lot I would just play the guessing game, but do not force the bolt.

    Crossthreading is better than red loctite.

    However, you could try calling/emailing Magnum (assuming that's the company) on a friday, and hoping you get through to anyone that remotely knows anything about anything.
     
    Last edited: Apr 3, 2020
  3. Apr 3, 2020 at 6:02 AM
    #3
    Ryooo

    Ryooo [OP] New Member

    Joined:
    Jun 14, 2018
    Member:
    #16132
    Messages:
    113
    Gender:
    Male
    Boynton Beach FL
    Vehicle:
    2014 CM SC Platinum
    TRD Supercharger 4.5 BDS lift 20” Method Standards sitting on 35 Nitto Grapplers Rigid grill top and bottom with lights AMP running boards Fender flares Magnum rear bumper Rear LED bar Air bags with onboard compressor Brake controller Alpine Navi Alpine amps x 2 Focal Separates front and rear 2 x JL 13s in a stealth box behind the back seat LTE cellular booster Rear seat under locked storage Dynamat from ceiling to floor LEDs all over Bed liner Bed rails Paint protector covering nearly the entire front end and more

    Thanks man. It’s the threads on the frame not the bumper... but a guess equally a call to Toyota may get me somewhere.

    mill look into the kit. Thank you for the link
     
    Tundra2 likes this.
  4. Apr 3, 2020 at 6:10 AM
    #4
    timsp8

    timsp8 Member

    Joined:
    May 11, 2018
    Member:
    #15231
    Messages:
    2,804
    Gender:
    Male
    First Name:
    Tim
    NY
    Vehicle:
    2018 Tundra Limited Crewmax
  5. Apr 3, 2020 at 4:47 PM
    #5
    Ryooo

    Ryooo [OP] New Member

    Joined:
    Jun 14, 2018
    Member:
    #16132
    Messages:
    113
    Gender:
    Male
    Boynton Beach FL
    Vehicle:
    2014 CM SC Platinum
    TRD Supercharger 4.5 BDS lift 20” Method Standards sitting on 35 Nitto Grapplers Rigid grill top and bottom with lights AMP running boards Fender flares Magnum rear bumper Rear LED bar Air bags with onboard compressor Brake controller Alpine Navi Alpine amps x 2 Focal Separates front and rear 2 x JL 13s in a stealth box behind the back seat LTE cellular booster Rear seat under locked storage Dynamat from ceiling to floor LEDs all over Bed liner Bed rails Paint protector covering nearly the entire front end and more

Products Discussed in

To Top