GEN 3 (2022+) Wheels and Tires Photo thread

I hope I'm doing this right, here it is, 295/60/20 Nitto Ridge Grapplers with a RC 1.75 LK. This picture doesn't do it justice. Man do I love this TRUCK!! About a 1/2" of clearance on the inside to my strut. No Rubbing and no alterations/cutting underneath to prevent any. I mentioned this last November here after I ordered the truck, I have never done anything like adding bigger tires or kits. At 5'11" I'm not the tallest guy but dang it sits up high. LOL Probably not to a lot of you but this for me is super cool first time and loving every minute so far!!!

 

I feel ya. I’ve raced cars,motorcycles but This is my first truck my first lifted truck and I’m in luv.
I’ve had so much fun modifying her…Never thought I would get into this truck this much. Now I want a 6 inch lift and 37s lol…
[ATT]

 

Beautiful truck Norman

 

THANK YOU!!!

It looks like we have similar trucks albeit different colors. What do you have for tires? LK?

 

I’m running
Nitto Recon Grapplers
305/70/18
34.8 Diameter
12.2 Section Width
9.85 Tread width

My wheel is a Fuel Rebel 6
18x9 with +20 offset
I did have to remove front mud-flaps and push the back of the felt liner with some heavy duty Velcro and the very bottom rear fender well. Super easy. I’ve done no cutting of anything and did not remove the rear crash bracket that sits behind the felt.
295/70/18 is the max u can fit without any rubbing. I did it and had zero issues fitting on stock wheels but wanted a bigger tire so I went 305 and bought new rims…I didn’t want to go 37s originally because seemed like a lot of cutting and even possible bumper cutting. I didn’t want to do that…I wanted to remove the front mud flaps anyway for looks and my poke is only 1/2 inch of actual tread so wasn’t worried about the mud flap. I still have the rear flaps on so I’m not throwing rocks on anyone behind me.

 

I cut the rear crash bracket only and I have no rubbing so far. I've been off-roading but haven't done any rock-crawling. So, I cannot tell if I've technically "maxed out" the up-travel articulation yet.

A good alignment shop should be able to push your caster forward. What UCA's do you have?

 

I got an unrepairable flat on my front tire this week with less than 1,500 miles on them, so I decided to upgrade all four with a set of Toyo Open Country AT3s 275/65r20.

 

23' TRD Pro - Stock (before) - 35" BFG KO2 (after)

 

what's the tire and wheel set-up?

 

That's the exact swap I am thinking of doing. How is the ride with AT3 compared to stock tires?

 

The shop says they'd be a stiffer ride, but I really don't notice much of a difference. I am really happy with them so far. I wanted a little more height without a lift and it fills the space up nicely.

 

Vossen custom HF6-4, 20x9.5 +30, hub 95.1
Pirelli Scorpion Elect/RIV 275/65R20

 

Group, I have a question regarding lug nuts, apologies for the ignorance if this has already been stated [tried searching].

I have just bought a set of wheels from a company and I have no clue if I can use my existing lug nuts [2022 TRD OR - M14x15] or if I need to get a new set [60degree mag / flat seat lug hole length, etc.]. I have asked the distributer twice, no responses. Cannot get a number for the manufacturer to even call them. So a bit at a loss in terms of length and type I would need, if any, for these new wheels.

Any help would be great.

 

That looks like a TRD knock off so would think it would use stock lug nuts but not 100% sure. I can tell you that the stock lug nuts will not work with after market wheels but again those looking like TRD knock offs you may want to try and see if it fits. You would know immediately yea or nea! Good luck. Maybe someone else can give a more definitive answer.

 

Rolled the dice, assumed they would work! Yup, no problem. Thanks for the quick reply.

 

Looks good
Keeping the moustache silver?

 

What’s the company? eBay wheel?

 

Rolled the dice, assumed they would work! Yup, no problem. Thanks for the quick reply.

OEPlus is the Co.

 

Nope, mustache next.

 

Probably a bit more poke than what I was thinking but that probably is because of the rubber ?! Regardless, that’s going from an OEM +60 to a +15.

 

295/70 R18
2/1 Cornfed leveling kit.

 

truck looks great, what tonneau cover is that ?

 

Thanks! it's the diamondback HD.

 

285/60r20 BFG KO2s, no lift/level. Traded in an F-150 Tremor for this...ZERO REGRETS

 

What’s up guys, here’s my build out on Oahu. I got 17” Advans wrapped in 35x12.5x17. I installed the trd 3” lift as well. Minor wheel well modification but no cutting was done. Aloha

 

Servco installed the trd lift?

 

No, I took it to Mj motorsports