What have you done to your 2.5 gen Tundra today?

Yeah I bought the kit earlier in 2024 but would have gone DYI to save $500 big heads ....oh well it is what it is

 

Do it! Mind you this is a bit on the extreme end of the spectrum lol

 

All cleaned up
Look at these booties

 

a bit more than just the axle seal. Hub bearing, retainer bearing, clips, o-rings. The whole that that is related to the hub bearing.

 

Glad I'm not the only Tundra/4Runner family

 

Well I bought one of the under seat storage units for my 2020 SR5 and it was a fairly simple process.Cutting the template out was a PITA but all in all not bad.

 

80% completed the FRAC install today. Just need to install the camera in the grille. The dash disassembly requires a level of patience I just don’t have. Also completed two side quests during the install - Accessorides remote start with takeover and adding a switch to the YotaLED grille lights.

Also, I hate plastic clips now.

 

I think we may be brothers.

 

Shoot I have zero issues taking the dash apart. Way better than 90% of the stuff I’ve done. Just pops in and pops out and stays tight.

 

Found a sweet spot in the bags at 70 psi, might go a little higher as it still leans into corners pretty heavily. Getting excited for that sway bar install, it might drive like a truck again instead of a damn pontoon boat

 

Hot damn!!

 

Except he didn't buy the one that is for the platinum trim.

 

Looks good did you run the OE hard lines or use rubber for the entire install??

 

I used OE hardlines and rubber hoses.

Here's the oe rubber hoses and oe hardlines in the background.

 

That's what I ended up buying as well.... some of the guys said they had issues trying to get the hard lines to line up, but I'm thinking it was a matter of snugging things down in the wrong order....

 

Hit the dunes near Baker, Ca. I was a day late to camp so everyone else in these pics is back at camp with hangovers. Pretty sure this was little Zach’s first time airborne.

 

Someone's having a blast!!!!!!

 

I always take him with me. He fricken loves it!

 

great pics, thanks for sharing. that looks awesome

 

I struggled with them too. The mounting tabs did not line up by about a quarter inch. I tried multiple times and nothing was working. The solution was to back out the bolt holding the mounting bracket near the alternator. This gave enough clearance.

 

• New front brake pads (they weren’t totally gone, but they’re so easy to change I just went ahead and did it)
• Tire rotation
• Oil change
All set @ 75k

Should probably clean this pavement princess engine bay

 

Here are a few threads to get you started...
https://www.tundras.com/threads/parts-list-for-adding-oem-trans-cooler-to-5-7l.125248/
https://www.tundras.com/threads/transmission-cooler-bracket.136129/
https://www.tundras.com/threads/transmission-cooler-bracket-hayden-679.153340/

 

Should be easy to spot you around town..

 

Or.... in the US:

https://www.amazon.com/CERAKOTE-Cer...-+quick+and+easy+to+apply,aps,566&sr=8-4&th=1

 

Before I hit the dunes I has to install some whips. My old one busted on a trail and is gone. I grabbed some 4ft Nilight ones and connected them to my chase light circuit. Fabbed up some brackets to the bed so the topper can still close with the mounts installed, and the swing cases still operate. They’re brighter than I imagined, comes with a remote and a ton of options.

 

I see some air time!

 

Yessir! Surprise drop off.

 

125k Oil change and switched to 5w30. Also greased my UCAs, tie rods and drive shaft

 

I bought these and they are working well so far

$35 TRQ Front Driver & Passenger Side Fog Light Bezel Set Compatible with 2014-2021 Toyota Tundra TO1038175 TO1039175

https://www.amazon.com/dp/B0BCQ8QJVR

 

Please PM me