The Great HU Install of 2023

Ahh, thanks!

 

No
The JBL system powers ALL the speakers off the amp.
The non-JBL (with amp) powers the DASH speakers off the HU and the rest off the amp.

 

Cool, good info, thanks.

A bit further on the install, and I could pull the power for the rear doors off the back of the HU and run wire to the doors, but that doesn’t seem worth the effort like @AZBoatHauler mentioned. I’ll just do the fronts and sub for now, then add another amp down the line for the sub and switch the rears to the 4channel.

 

Just an FYI, if you are using this Alpine RUX-H02 bluetooth volume knob, you have to "wake it up" (push / turn it) before turning on your Alpine head unit, otherwise it won't pair w/o going into system menu manually.

 

I still can't get mine to work consistently. I paired it before pairing my phone, and it still doesn't connect. I'm considering returning it...

 

Anyone have an F511 that they aren't going to use ?

 

Okay, 1 stereo installed, one to go. Kenwood for the Tundra. One question I have (@BiggHertz ) is what is the difference between the iDatalink ACC-HU-KEN1 and the iDatalink ACC-HU-KEN2? Or did I skim over the answer somewhere?

 

different radio side harnesses.

 

But what makes them different

 

Different plugs and pin-outs. Not all kenwoods share the same harness.

 

Got it - thanks.

 

For anyone using the Alpine knob and tired of forgetting to turn it on at system startup, I think I figured out a workaround. Since the knob uses a CR2032 for power, this adapter should work to power it up via usb, which only comes on when the radio is on. I ordered one (after checking to see if the site was legit - jury is still out there but used PayPal so meh) and will report back after I've had a chance to try it out.

https://www.countrychristmasloft.co...converter?currency=USD&variant=43001696256153

 

won't you still have to turn the knob on? Doesn't it auto-power off after a certain time without active connection?

 

It turns on right away when you reinsert the battery, so in theory it should be up and ready to go on power-up.

 

good to know. Not having messed with one, I wasn't sure.

 

Should’ve just bought a radio with a knob on it.

 

I don’t miss my knob

 

lol

 

Kenwood 1037s installed last night

08 sequoia with JBL and maestro rr2

rear car won’t come on in reverse but if you hit camera button it shows up?

 

Make sure you enable “reverse interrupt” or something along those lines in the camera menu. I don’t remember exactly what the path is from my old Kenwood.

 

Interrupt is turned on. I guess I’ll call Crutchfield this afternoon

 

I’d say check your wiring then. Did you use the MRR to Kenwood harness or splice them yourself?

 

MRR harness

 

…right… but what about from the MRR harness to the Kenwood? Hard to help you troubleshoot if we don’t know wtf you have installed and how. Did you pick up the extra harness that is plug and play between the MRR harness and the Kenwood, or did you have to splice the Kenwood harness to the MRR?

 

sorry…I’m dumb today…it’s all plug and play using harnesses from Crutchfield

 

Then that definitely calls for a call to Crutchfield. Weird.

 

OK here we go

issue is fixed

Called Crutchfield

on some models you have to pull 12v reverse signal straight through by itself if you’re getting low voltage/no reverse signal and completely bypass the harness

attached are photos of the connector. The green wire is the reverse wire to tap into

Some vehicles will have all 3 wires. Some will only have 2,as mine did.

hope this helps somebody

on the

$1,499 Kenwood DMX1037s 10.1" High Definition Car Stereo Receiver with Capacitive Touch Panel

Kenwood DMX1037s models

 

Got my

$1,499 Kenwood DMX1037S 10.1" High Definition Car Stereo Receiver with Capacitive Touch Panel

Kenwood DMX1037S in......kinda. No one mentioned how shitty the clips were at the top of the radio. Needless to say, a shipment of those will be here Tuesday lol