Rainman’s Pile of “Free to a Good Home”

This is a bunch of random stuff that is just taking up space. I could toss it, but thought I’d at least see if there’s anyone that could use any of it first.

Shoot me a PM or post in here with the item number(s) if you want something (or all of it). I’d like some help with shipping but otherwise all of this is free to a good home.

What's left:

• ONE #1
• #2
• #3
• #4
• #6
• #7
• #16
• #18
• #20

1. Scosche “Magic Mount” 10W Qi wireless charger w/ 12V DC to USB-C power adapter. I actually have two of these left over from my custom MagSafe charger install. You would need to either run a USB-C power cord into these or tap the wires on the power adapter into a 12V source in the vehicle. Includes the magnet mount plates for attaching to your phone/case as well.
2. GEN 1 Eero Mesh WiFi router - this one is the original Gen 1 and can no longer be software updated. It still worked perfectly when I took it out of service, but I don’t know what happens if you try to “mix” it into a system with other newer Eero hotspots.
3. SINGLE USB 3.0 socket/extension cable w/ 3’ cable. This will fit into/replace the opening for a cigarette lighter plug (such as inside the center console) and can be plugged into a power source (see further down) or into an after-market stereo HU that uses a standard USB port. This one has a single port in it, and is new in the wrapper.
4. DUAL USB 3.0 socket/extension cable w/ 3’ cables. This is the one that was in my truck in the center console until I recently swapped things around again. This does not include the external mount bracket or cover “flap” thingy. It does include two different style backing nuts.
5. DUAL USB 3.0 socket/extension cable w/ 6’ cables. This one was in my daughter’s Subaru Forester plugged into the back of a Kenwood dual USB head unit until I swapped that out recently. Includes the flange backup nut and the flap cover “thingy”
6. Gen 2.5 rear turn signal resistor “break out harness” set - 50W 6ohm resistors soldered into breakout harnesses to prevent having to t-tap the factory wires when running LED rear turn signals.
7. AJT V2 slim smart key fob in Cement - this lived in my pocket for the better part of 2-1/2 years before I recently swapped to the new MESO one. This version does NOT have a spot for your physical key.
8. Baja Designs wiring harness for Squadron/S2 part 61-3600. This came with a set of S2’s that I bought used, and I ended up making up my own harnesses from scratch. This has a relay and a switch and new connectors and whatever else (check the BD website for more details I guess).
9. License Plate light sockets and connector pigtails from rear bumper harness - I cut these off when I switched to the CBI bumper.
10. Random assortment of fuses and fuse taps - there’s two Boost Auto reverse light fuse taps with a ATM 3A fuse each, there’s a pigtail with ring eye and another ATM 3A in-line fuse, two pigtails from the ARB compressor with a large 40A fuse in each, a short double-eye piece of hookup wire with a 60A MIDI fuse and holder, and ATM (full height) fuse tap with a 5A fuse. Also including a set of ATM fuses.
11. Small section of two-wire cable (maybe 4 feet long?) for Baja Designs light, plus a matching plug connector.
12. TWO QC 3.0 USB + USB-C PD sockets. ONE of these was installed in the back of my console for a few weeks until I switched to one with two USB-C sockets. The other is unused. To replace a factory 12V socket with one of these, you will need to open the hole up a little bit with a step bit…just be aware.
13. ONE red anodized QC3.0 dual USB power socket. This was one of the first mods I did to the truck, so it had been in my truck for just over 2 years. Works great, it also displays the voltage when it is powered.
14. 12V-to-5V “buck” power adapter with 2 USB ports. This takes 12V DC and steps it down to 5V DC to power the two USB ports (up to 15W). This was in my truck for ~2 years powering my relocated USB ports (above), it’s easy to wire into an existing 12V power socket wiring and use to power USB ports.
15. USB adapter cable for 2020/2021 factory HU. This cable plugs into the back of the 2020/2021 factory head unit and provides a standard USB-A female port on the other end. I used this to relocate my CarPlay port to the inside of my console.
16. USB adapter for Factory USB Port (2020/2021) - this cable will connect to the factory plug from the factory CarPlay port and provide a USB-A male plug to go into the back of an aftermarket head unit.
17. 90-degree “up” USB 3.0 cable - this cable, when plugged into a USB-A port that is “right side up” will route 90-degrees UP. Obviously this won’t work if if you’re trying to tuck your wireless CarPlay adapter down inside of the shifter area…
18. Gen 2.5 front license plate frame - new in wrapper with screws. Part 75101-0C011. I got this when they re-did my front bumper from hitting the deer, but I replaced that part of the bumper with the SSO Hybrid so I never installed this.
19. Complete bumper wiring for the rear parking sonar. I pulled this out of a used harness off ebay. The BSM part of the harness was damaged, but the parking sonar wiring is fully intact. Also includes the main connector to the harness running up the frame. If you were wanting to put in parking sonar or needed to repair an existing harness, this would be a good head start.
20. CH4x4 custom double MOMENTARY switch. I had this made when I was setting up my first Blue Sea battery cutoff setup, which used a momentary ON signal to activate the solenoid, and a separate momentary OFF signal to deactivate the solenoid. The top half says “Winch Power” with an image of a winch, and the bottom has the TEQ symbol and says “OFF”.
21. Clear Gen 2.5 third brake light housing.

 

I'll take number 8 and 11.

PM inbound.

 

Nice pickups, Joel! I was looking to see if #8 could power up XL Pros but the BD harnesses are always a little too short anyway. Guess it’ll be a custom job. Send me some updated photos of the rig when you get a chance. Interested to see what you’ve been up to.

Lots of good stuff here, Casey, and very generous of you. The hoarder in me wants to take a few things lol and that custom winch switch is mighty tempting, but just finished wiring up the BS 7700 to the switchpro today. Burned two switch spots but at least it’s done

 

I’ll take 12 off your hands. I’ll put one in the back and one in the console to match the one I have by the shifter. PM incoming!

 

Hey Nick, if you can make use of the BD harness you can have it no worries. Let me know, no issues here.

 

Haha no no. I have a couple of them. I was just checking to see what gauge this one was. Appears to be the same harness I already have. All you buddy!

 

Interested in 10 and 14.
PM on the way!

 

I'll take #21, clear 3rd brake light lens... TY!

 

Damn just missed 21

 

Is there anywhere besides klearz that makes these clear 3rd brake light lenses?

I would rather not spend $125+ on one.
TIA

 

I’ll take #15 and #17

 

I’ll get caught up tonight and get these all updated and ready to send out.

Off to the mountain this morning

 

Enjoy your trip

 

Ok - I’ve updated the list with everything that has been spoken for either here or PM. I’ll respond to PM’s next to confirm, but shipping prices will be tomorrow for me to figure out. I need to find boxes for all this stuff, and I’m wiped out…20” of fresh snow yesterday made for a great but tiring day on the board.

 

Man this is one of the reasons I love this dang forum so much. Always a pay it forward thread going on and lots of people who are so appreciative when you do it.

With that, I'd like a #1 please, PM sent with my address. I'll pay for a flat rate box from USPS if needed.

 

One is yours then. I’ll get info tomorrow.

 

And its 90 here today

 

Back of the Magic Mount looks like this. The slot is where the USB-C cable plugs in.


These originally came from the TAQ03 charger tray/setup

$35 Scosche TAQ03 MagicMount Charge Compatible with 2014 to 2017 Toyota Tundra 10W Qi-Certified Magnetic Surface Mount with Bezel for use with Smartphones

https://www.amazon.com/dp/B07NKJ8KPJ

 

Thanks Casey. I kept digging and found it. But then I couldn't figure out how to line out my question. Wasn't sure you saw so I just deleted.

 

All PMs responded to. A few of you guys need to at least send me a zip code for a quote on shipping...

 

Everything spoken for is shipped (most of it should be in the hands of the recipient).
There’s a free things left. If not one has spoken for or by the time I leave for T2S on Saturday morning, it’s going into the appropriate recycle or trash receptacle on my way out of town.

Also willing to deliver in person at T2S if someone wants but you gotta request it before I head out