What have you done to your 2.5 gen Tundra today?

I got them secondhand. The driver side was fine and probably could have left it, but the passenger side was losing grease pretty bad and was probably torn. It doesn’t sound like they need to get changed often.

 

Nothing too fancy, got to use the new bike rack to take the truck out for camping. Camped in the new year.

 

Looks awesome! What bed cover and rack are you using? This is something I’d be looking for in the near future.

 

The bedcover is the RetraxPro. Cross bars and raved rack are Yakima. The bike rack is the Yakima Swing mount. I was very skeptical of the swing mount until this trip. Definitely works as advertised and it’s very stout.

Next up on my mods list is lights (ditch lights and light bar). I have those already, waiting on switchpro and mounting tray to be delivered before I start all the wiring.

 

Drove home from hunting last night. There are so many fuel economy threads, I decided the last couple days to see just how well I can do. What is pictured below is normal for me if I keep it under the speed limit and stay off cruise control through the Tennessee hills. This means I stay in a right lane and my speed will fluctuate (I’ll let it drop a few mph instead of shift down to 5th or 4th like cruise control would do immediately). I’m using tires that are 8.4% larger (LT285/75R18 vs 275/65R18) in diameter and 25 lb heavier than stock. This 8.4% number appears to be consistent with the difference between my dash and GPS. I run 40 psi in my tires. I also have a static load in the bed of around 300 lb with my retractable bed cover, 2nd battery, and Plano trunk full of recovery tools. Corrected for tire size and assuming my GPS is accurate, this is 19.4 mpg. Better than the 18.5 I posted before. I still average around 16 on the entire tank due to how much city driving I do. I have zero complaints with fuel economy.

 

Do it! You wont regret it!

 

After seeing how expensive mud flaps were, I decided to make my own.

Started out with some black ABS plastic sheets 12" x 16" (link below)

$25 Zuvas Black ABS Plastic Sheet 12" x 16" x 0.06" 6 Pack, Flexible Than Plexiglass Sheet, Moldable Than Acrylic Sheet, DIY Materials for Home Decor, Handcrafts (Matte & Textured Finish)

https://www.amazon.com/gp/product/B08R9W4NZW?ie=UTF8&th=1

The I came up with a design that I liked



Then I used self drilling 3/4" #2 black truss head screws to attach.

$8 Small Parts 0812KPMB Steel Self-Drilling Screw, Black Phosphate Finish, Modified Truss Head, Phillips Drive, #2 Drill Point, #8-18 Thread Size, 3/4" Length (Pack of 100)

https://www.amazon.com/gp/product/B00GYJSL3O?ie=UTF8

Lastly I bought some red TRD stickers from @ToYodaVinyl on Etsy an put them on for the finishing touch
https://www.etsy.com/listing/132335...ro=1&frs=1&edd=1&sts=1&organic_search_click=1

Finished product below

 

Installed the SSO Slimline Hybrid. Of
course no install goes as planned when I begin a project. Still have some modifications to make so the winch clutch can be turned completely, but overall I’m ok with the outcome.

 

Where do you get these? I'm assuming they're to give you a place for wiring once you start adding a lot of extra electrical components.

 

I guess it’s time for a 4Knines back seat cover. I think the wife was saying something without saying something with this pic.

 

Might be the angle of the photo but is the passenger side not as flush as the driver side?

 

In person it definitely it is more flush than the photo displays. It also sits slightly closer to the drivers side and could also have to do with how I was able to align the plastic bumper back on.

Please don’t activate my OCD. I did the best I could.

 

Just those damn phone cameras. I'm sure I wouldn't have thought that if I saw it in person. Love the look of the SSO

 

I’m looking and looking to see what your seeing. But, I don’t see it. It looks perfect to me.

 

Looks familiar

just pull the clutch handle and trim the one side.
https://www.tundras.com/threads/rainmans-2021-lunar-rock-trd-pro-build.77317/page-22#post-2946220

 

Putting the factory parts back on was a bitch with this thing!

 

Found a drivers side grab handle from a 2nd gen at pick n pull for $15! After some cleaning it looks great. Gonna put it on when/if it stops raining

 

Yes, that part was not fun. The factory bumper being more flimsy due to the cut out got me for a while. I had to touch up my cuts a few times because I didn’t cut enough the first go round and the trim wouldn’t seat well. All in all, it’s not perfect but works and looks good to me. I’ll tackle the clutch lever when I get my bracket for the control box.

 

Moved Tundra into the garage. Noticed my headliner was wet on one side. Turns out I didn't do a good job sealing the Front Runner rack on install. It actually rains where I live now...as in days in a row (compared to the desert). Correcting the issue tomorow.

 

Wanted the phone/waze up closer to my line of sight so installed the Rago fabrication dash plate with some ICS fab accessories today

 

Overlandequipped.com I have the same setup. I bought the bracket from them but got the Blue Sea CB and Blue Sea fuse block from Amazon. Overland does sell it as a kit if you want a one stop shop.

Mount https://overlandequipped.com/collec...use-block-bracket-for-2007-2021-toyota-tundra

Full kit https://overlandequipped.com/collec...xiliary-power-kit-for-2007-2021-toyota-tundra

 

SSO bumper finally went on, Thanks to @Punisher29073

 

nice work and awesome looking rig. What did that Trd suspension run you?

 

Wire for my ditch lights were too long. Shorten it up and created a split. A lot better than before

 

What are you going to do for your control box?

 

Thanks. Too much, I'm afraid...but still worth it. Wasn't lucky enough to pick up a used set. Got it all new (shocks, speed sensor bracket, cushions, and hardware) for about $3050 shipped. Did all the work myself except the alignment & zero point calibration...$70 for that.

 

Thanks. I'm pretty sure I've seen yours too. Just got curious enough about it to ask.

 

installed Brightbox Fogster on '20 1794.

now the SS3 Pro's stay on when I hit the bright lights. Using Auto brights is now decent.

nice doo-hickey. easy to install.

 

I’m hoping one of the shop guys at work can make me up a plate/bracket for it and my thoughts are to mount it towards the drivers side (forward of the radiator) cross member. That way I can still access it from the top through the access slot atop the grille.

 

What engine do you work on?