2014-2021 Front/Rear Anytime Camera Mod - FRAC Harness

Agreed!

 

Thank you for the offer, I would love to take you up on it but I'm starting a new job next week so road trips a out of the question for a while. Maybe if there's a few other Canadians here who would be willing to chip in for gas and hotel I would consider it seeing as I can do it in 2 days (11 hours one way). Or maybe one of you guys in the Lethbridge/Medicine Hat region could make a run for us

 

@TundraTex sent you an email with my info so I can get one of your sweet inventions.

 

@TundraTex Is there a way add left and right cameras to the FRAC?

 

Finally got around to installing my FRAC. Thanks TundraTex! Based on other's camera feedback, I went with the NOAUKA Waterproof IP68 Night Vision 170 Degree. I used a standard L bracket and multiple washers to attach it under the Toyota emblem. No holes were drilled in the grill. I used the side of the drill bit to slightly notch out about half the diameter of my bolt to have a place for the bolt to rest without moving in the grill. The L bracket was then tightened by large washers and a nut attached to the back of the Toyota emblem's bracket.

The camera looks crooked or uneven in the pictures based on the angle I took the pictures. It is actually almost perfectly centered.



Before picture:

 

Looks good! great ingenuity. But it still looks crooked!

 

Nice job, @ktemple. Looks great!

 

Very nice Kyle. Any pictures of the camera in operation. I just got that same camera and hopefully will be doing my install next week.

 

Here are a few pictures in different light settings.

 

Thanks, hopefully going to do this next week. Heading up to Mt Washington in New Hampshire for a long weekend.

 

Awesome, many thanks for the idea. I have the same camera and tried a couple other options that did not work as well. I did add some 3M double sided molding tape to the top of the camera that makes it even more solid because it sticks to the grill when bolted on. Was surprised how easy the grill assembly came off. Now it's time to pull apart the interior and get the harness installed...

 

Kyle,
A few questions. Bought the same camera, instructions aren't to clear.
See the picture below.
On the left the red and black (power +&-) along with camera plug, yellow to yellow and red wire (?) Then long black wire with yellow and red (?) at other end to FRAC harness. My question is why 2 red wires next to the RCA plugs and do you connect 1, both or none to + 12V since there is + & - next to the the camera plug (left side of picture).
I just don't understand 3 red wires .
Thanks.
If anyone is wondering it is the Noauka IP68.

 

Jim,

If you’ll check out the FRAC install video on Youtube, you’ll see how this all works.

But the short version is:

The red wires next to the RCA plugs are two ends of the same wire. That wire carries power to the camera from the FRAC Harness. On the camera harness end, the red wire connects to the red camera power wire. (The black cam ground wire is connected to ground in the engine bay). The HU end red wire is connected to the red camera power wire from the FRAC Harness using the spade connector provided in your kit.

I really recommend you watch the installation video if this doesn’t make sense.

 

Thanks Lou.
I did watch it a while back, I was planning on watching it several times before and during the install. Guess I don't remember.
I can't wait to do this mod......hopefully the rain will stop when I try do do this.

 

Just watched it again. All makes sense now.
Thanks Lou.
Now if the weather just cooperates.

 

Can I have your autograph?

 

Got a new cap for my truck and we are back in business! Just sent you an email for the invoice

 

For what?

 

Movie star......FRAC video

 

Lol i don't kniw about movie star

 

Skippy, is this the route you went? I live in Ca, where it’s mandatory, and it would much easier going this route.

 

I have an 18 Tundra, this will be my first mod, can I order?

 

Yes you can! Just refer to Post #1 of this thread for ordering instructions.

 

I just received the first FRAC Harness order for a 2019 Tundra. The Entune interface is the same as all previous 3rd Gen Tundras, so we're off to another model year!

 

I didn’t like the way the logo camera looked on my grill. I bought the noauka camera and will mount it underneath the logo like the one showed below (picture from another member) . I thought this Set up looked a lot cleaner.

 

So how do I send you money

 

@Alexstundra, Just refer to Post #1 of this thread for ordering instructions.

 

Nice, clean install, Samuel!