Oil filter cartridge

Are you not able to remove the oil cap?

I have these universal wrenches in case I have problem with the regular cap wrench.

$10 Lisle 63600 Oil Filter Tool,U.S.,2-1/2 - 3-1/8

https://www.amazon.com/Lisle-63600-...pID=41gd0o9Ph8L&preST=_SY300_QL70_&dpSrc=srch

Craftsman Oil Filter Wrench, Auto-Adjustable

https://www.amazon.com/Craftsman-Oi...pID=41Gguguh45L&preST=_SY300_QL70_&dpSrc=srch

 

For the ones breaking teeth off that housing post up a picture of the tool your using. I think that would be impossible with the MOTIV X tool I use.

 

I had the aluminum filter housing on my last truck, ifI say it was a little easier to work with during oil changes. Will probably buy another one for this truck soon.

 

I couldn’t get it off I was afraid I would mess it up more than I had, the dealership where I bought must have overtorqued it but it had only been 2500 miles since the oil was changed so I just left it for now and put my new mobil 1 full synthetic oil in, I migh try one of those special filter tools next time.

 

Check this one out.

Motivx Tools Oil Filter Removal Tool - Adjustable Wrench for 2.5" - 3.25" Small Diameter Spin-On Oil Filters

https://www.amazon.com/gp/product/B01BS5B3ZQ/ref=ox_sc_act_title_1?smid=AMO9Q84JXX23S&psc=1

 

This is the one I bought. No problems at all.

 

I have the same. When torqued to 18 ft lbs it shouldn’t be an issue. The issue comes from being put on way to tight.

 

Here's the aluminum cap @15whtrd was referring to and a photo of the tabs on both sides of the tube. You have to keep the tube from your existing cap when you replace it. Did you swap over the tubes @BTBAKER maybe that's why it didn't seat properly?





Edit : Nevermind, the tube that comes with the aluminum cap is shorter, not longer.

 

That very well could be. I did NOT swap it over. That’s why I love this site.
I have one in my garage. My plan is to rotate them so I can thoroughly clean them in between. I wonder if they sell just the middle part so I don’t have to swap it every time?

 

I’ve posted before but here is a great write up.
http://w11.zetaboards.com/Outdoor_Garage/topic/11525874/1/

 

X3. Right tool for the job. Those adjustable ones are ok for Honda’s or small block chevy’s. Not this crazy shaped filter cap.

 

What do you use to clean? I spray all my pieces down with non chlorinated degreaser. No residue and dries in less than a minute. Also works great to clean up driveway drips or exhaust or wherever it gets.

 

Those crazy shape wrenches come in handy when the oil caps are rounded out. They bailed me out a few times.

 

I do the same but I like to swap and let it dry. It’s probably not necessary but I do it anyway.

 

Yeah nothing wrong with being cautious. I let it sit for probably 5-10 minutes while I’m just letting it drip then re-install.

 

I’m sure that plenty. I like the spare to. If something goes south during an oil change I want it handy. It’s not something I can run to the auto parts store a buy.

 

When I did mine I lightly pushed it to a tilt and with a little more pressure in snapped out without any damage at all and reinstalled it the same way.

 

That's the one from Amazon? The link that I posted doesn't look same?

 

Dumb question...so the cartridge wrench I got for the plastic one will not work on the aluminum one?

 

Here's the one I bought.
Genuine Toyota 15620-31060 Oil Filter Cap Assembly

$23 Toyota Genuine Parts - Cap Assy, Oil Filter (15620-31060)

https://www.amazon.com/dp/B008BHP68A?ref=yo_pop_ma_swf

Along with this
PBT PBT71114 Oil Filter Drain Hose

PBT PBT71114 Oil Filter Drain Hose

https://www.amazon.com/dp/B005R3SSUY?ref=yo_pop_ma_swf

I also got the fumoto valve and lock, and the filter wrench I listed above.

 

I also would like to know the correct aluminum housing. Wanting to start doing my oil changes. No more free toyota care for me and dealer charged me $120 for oil change... i have always done my own but this new style will take some learning to get used to...just feels good and can save time and money.
So...a question... service guy who changed my oil did not drain thru the drain plug...he always just unscrewed the filter housing and let the oil splash out that way.. is that ok or bad?

 

Are you saying not draining from oil pan?

 

And the post before your has link to metal cartridge, but read a few posts before about the metal tube with all holes from your plastic one needs to go on new metal cartridge something like that

 

Yes...he never removed the drain plug. I always went back to the shop while he did the oil change...he just unscrews the entire filter housing and drained the oil that way. Now that i think about it, i hope he was not leaving old oil in the engine.

 

Yea i was wondering the same thing...Why is the aluminum not supplied with the proper tube? Either way i just want to make sure i know what im doing. I have never worked with this newer style cartridge filters.

 

Man that doesn't sound good at all, I bought my trucked used, at first, they did the first two oil changes, cause I was nervous to do, now I do on my own

 

Yeah same here, I'm about to order it tomorrow

 

Changed (tried) the oil in my wife's Camry after having the dealer do it previously only to find out the oil filter canister was so freaking tight I couldn't budge it. After trying and trying, the little tabs broke off cracking the canister and I was fucked. Figured I would tow it back to the dealer that did the change figuring they may be decent people and help me out. Wrong. That oil change cost me about $300 with the tow. Oh, and of course they didn't have an aluminum one in stock so I had to buy another plastic one there only to replace it with the aluminum one on the next change.

Point is, buy the aluminum one before you get fucked by the plastic one. My Tundra has had the aluminum one in since the first change, its been great!