Transmission Cooler Bracket

The second picture is the right hand side of the cooler

 

Is there enough interest in just the bracket for me to get a batch made? I designed one, a few people have used it. I could also get some brackets that @pman9003 designed to give people options. There really isn’t any money in it by the time the bracket get cut and then powdercoated. Just something to help people out.

 

I’m for it if you can get a bracket made for the

$59 Hayden 679 Universal 11” Rapid-Cool Add-On Transmission Cooler to Enhance Cooling (not for direct replacement of the factory unit)

Hayden 679

 

I'll buy one.

 

I’ll have to look up the Hayden cooler. Took me an hour or so with measuring and doing a cardboard version before committing to get it cut.

 

If you do, I’ll be your first customer lol

 

Sign up for a free account on OnShape. It’ll make your life way easier as far as updating designs goes.

 

Thanks - that’s good information.

 

22-M22-AN06-SE ProLine Oil Cooler Adapter Fitting
Does it require one or two of the fittings?

 

I used a total of (2) M22 to -6 adapters, one for each port on the cooler. I used a 30 degree fitting on the top and 45 degree for the bottom.

Looking back I would use this for both, no adapter heeded: 22-M22PL06-45

Setrab is out of stock currently, others have it in-stock. Here is a one place, you can shop around. Two would complete the cooler fittings and not need anything else.

https://www.ebay.com/itm/3629218754...ar=632045939343&widget_ver=artemis&media=COPY


That goes from the M22, to a -6 (3/8) push lock for the hose to slide onto. Makes it simpler and less fittings. I think the top 45 degree fitting would work fine, just pick the angle you want before tightening all the way. It’s a o-ring seal so no need to go crazy on the torque.

 

2. Each port on the cooler needs one.

 

I’d be in on a bracket or 2. Keep me updated.

 

For those interested in the

$59 Hayden 679 Universal 11” Rapid-Cool Add-On Transmission Cooler to Enhance Cooling (not for direct replacement of the factory unit)

Hayden 679 mounting bracket I should have a test bracket from the metal shop in a few days. If there isn’t any fitment issues then a week after that I should have some ready. I have some bulk stainless mounting hardware to include with the brackets as well as some rubber grommets where the rubber lines pass thru the plastic shroud.

 

Are you designing so the in/out lines are on the side or bottom?

 

I’ve looked at both ways but for now - I have the inlet/outlet facing the passenger side.

The side mount inlet/outlet prevents an air pocket from being trapped. You want the inlet on the bottom, outlet on the top.

 

Thanks, that is why I asked.

 

@Jmunk, I am also interested in a

$59 Hayden 679 Universal 11” Rapid-Cool Add-On Transmission Cooler to Enhance Cooling (not for direct replacement of the factory unit)

Hayden 679 mounting bracket.

 

I’ll get a batch made with some left raw and some powdercoated black. I’ll always be able to get another batch made if needed.

 

Let me get that raw one @Jmunk

 

I've been using the "pman mount" since the first part of August with 0 issues. I really like that it uses the Setrab 20 row cooler. I also went with the Setrab direct fittings. One 90 and one 45 which made it even easier to install. I would highly recommend going this route as it's half the cost of the GCS

 

Any photos?

 

The metal shop I’m using this time went on vacation. After the holidays I should get a batch back.

 

@Jmunk, do you have an update on these brackets? I am interested in getting the powdercoated black one. Thank you!

 

I have raw steel ones ready, I should have powder coated ones back in a day or two.

https://www.tundras.com/threads/transmission-cooler-bracket-hayden-679.153340/#post-3817674

 

Hey pman9003
Does this look about right?

 

Do you have any photos of that with the 90 and one 45 fittings.

 

You are going to want different connectors. You have the straight ones in your cart, you need the 45deg or 90deg versions. Either of the two part numbers below. I am running two 90deg fittings. @BushBandit has said running one 90deg and one 45deg works even better, and I can see that being the case.

22-M22PL06-45
22-M22PL06-90

https://setrabusa.com/products/susa-hose-ends-m22-to-pl?variant=41774934556726

 

Got my friend to cut me one. Now I need the cooler and parts.

 

Any pics with the pman bracket and the 90 or 45 direct fittings? I am about to put an order in for my 2019 Tundra and 2016 Sequoia. It looks like I will be able to use the pman bracket on the sequoia too.

 

I’m not sure it will mount up on the 2016 Sequoia. The Sequoia has the top mounting bolt moved to the passenger side about 3/4 of an inch vs 2019 -2021 Tundras. If it does happen to fit it would be slanted, that may or may not bother some people.

I’ve been working on a mounting bracket for the Sequoias using a Hayden cooler like the brackets I’ve designed for the 2019 - 2021 Tundras. For some reason they moved a few bolt holes on the Sequoia radiator support.