WHAT HAVE YOU DONE TO YOUR 3RD GEN TUNDRA TODAY?

Those are the new G3's right?

Got any more pictures? I'm looking to purchase the same size but debating between these, the Recon's, and the Ridge Grapplers.

 

old tires had 20,200 on them.

Yessir. Debated on the ko3s and the falken wild peaks but I don’t plan to go off roading more than 2-3 times a year and these are more road focused from what I understand. They weren’t really noisy but you could hear a low hum.


What are you looking for? I can go take some more photos.

Nope. 323 for the alignment, mount, balance, disposal, and they even charged me for the part they broke.

I admit I should have looked it over before I swiped the cc but hindsight is 20/20.

 

I mean, they didn’t charge him to put the wheel lock key back in the truck. Pretty big perk right there. :-|
I’d say they used an impact wrench… which any shop should realize is not suggested.
They probably got annoyed key wasn’t in right place to begin with ‘I’ll fix him’.

 

And the kicker was that it was in the stock location from factory. In the bag behind the right passenger seat.

I’m about to go back up there and see what they’ll do.
I’d like the wheel fixed/replaced but I think at the very least they should refund the lugs they damaged which I seemed to have paid for and refund me enough to go buy four more.

 

I have the same kit but ended up moving my switch panel to the center console with a 3D printed flush mount. Curious, if you've noticed a faint rapid ticking noise coming from your switch panel when it's awake but not connected to bluetooth. Doesn't matter if the truck is on or off. It's very faint and any ambient noise would wash it out. Mine does and I have to turn my ear towards it to hear it in a quiet environment. Worked with sPOD/BD about it and they've acknowledged it after listening to recordings I sent them, but there's no known cause for it. They sent me new cables, circuit board, and two different switch panels, and the ticking persists after each individual change. Tried connecting a touchscreen switch panel and it also ticks. I don't notice it anymore but I gave up trying to find the cause.

 

Started to rip mine apart for new headlights to go in finally. Also took off the front air damn since some road debris snapped the spoiler in two.

going to take several hours to clean up the clusterF of wiring that alpharex has but hopefully all goes well

 

Kept mine in the garage because of Hurricane Helene. I vacuumed her out real well.

 

Got the Kicker powered sub installed by shop today. It sounds good. Adds thump and what is missing from the JBL stereo. The shop did a great install and part of the process was removing the 3 ANC mics so they would not fight the new noise. All in all I would recommend. Keeps factory controls.

 

Finally color matched the from grille trim and the rear bumper. I got the parts from OEM painted parts. This is my second time ordering from them the color is damn near perfect.

 

Interesting. This is my third sPod on a truck build and I never noticed any sound. I will check it out though and let you know if I have similar ticking sound. Cheers

 

Sounds good. sPOD/BD says they've never come across this before, so it's likely an isolated issue. Just doesn't make sense after troubleshooting with all new components. Every switch panel I plug in ticks. When I connect to bluetooth, it stops ticking and turns into a faint hum.

 

So you couldn’t gut the factory sub and put it in the factory location?

 

Built a “shelf” under my Xtrusion Overland XTR3 for my camping tables. Came out perfect. Pic is when I tested it out, it’s currently off truck getting painted black to blend in better. Best part is I can still use my slide out, no interference at all.

 

Diff service

 

You got any pictures of that center console mount? I don't think I've seen any like that.. I've seen the overhead and the driver side trim mount above the other buttons.

 

Don't have a great photo but just snapped this to get a driver view.

 

Can you tell me where you got the piece that is in your cup holder?

 

https://cupgrip.com/

edit...great product and no affiliation. Rarely even use but have moreso for passengers and tbh makes the holders 'look' better.

 

The Cupgrip is awesome for big tumblers like Stanley or Yeti.

 

Ordered, thank you.

 

What is the metal?

 

Machining debris. Nothing out of the ordinary, imo

 

Yup, normal for break in and nothing worrysome. Here's what came out of my rear diff at 4,300 miles. Shavings are fine. Chunks are bad.

 

Bought this Platinum. Traded my 4Runner. I really like this truck. I’m not going to mod this truck but really have to fill these wheel wells and will be looking at you’ll trucks for ideas.

 

installed Rockville subwoofer under rear seat. its okey, will install different one, its barely noticeable

 

I briefly thought about it but the labor needed didn’t really make enough sense. I still have too much storage area and won’t miss losing behind seat. Plus this has little modification impact in case it’s ever sold. Just drive 500 miles and I really do like it. And I’m a guy who had a “system” in all my other vehicles. The factory sub is still on and working. It’s like having an extra tweeter lol

 

Is “Rockville” Temu’s “Rockford”?

 

What did you use?

 

Hi, where can I buy this bracket for the rear dash camera? Thanks.