GEN 3 (2022+) Wheels and Tires Photo thread

Aftermaket +18

 

3.5 lift

 

Stock flaps and zero rub, even at full lock forward or reverse

 

My 295/60/R20 with +15 rub on the liners and mud flaps. Mud flaps are off right now but going back on with some trimming.

I don't mind the liner rubbing but need the mud flaps to protect paint so time to get cutting!

 

Crap. Post a picture when trimming is done and flaps back on I’m curious
Thanks

 

Note that wheels and tires fit pretty good except the little rubbing while turning. The OE mud flaps have a bump in them that others have cut off and that worked.

No trimming of the truck!

I think the liners can be pinned back to keep it away from the tires.

Not too big a deal and I have had the wheels on the truck for about 14 months.

 

I see. Easy peasy.

 

Yeh it’s not only the offset of yours but also the width vs my factory 20x8. I can go full rotation with 35x11.50x20 or 295/65/20 or what I have 295/60/20. The 295/60/20 was the safest bet for no rubbing on stock suspension with my oem 20x8 wheels. As you go aftermarket u run into most are 9” wide and usually a little more aggressive offset. I think you will be ok with some pinning back and taking out that little black box behind the front wheels.

 

Icon 3in lift 37x12.5 17 no rub at all

 

i think I’ll be ok with pinning back the mudflaps by 3/4” just need to figure how to do so.

 

might want to take out that metal bracket too. Gives way more clearance and only two bolts.

 

Perhaps its the picture perspective, but the truck looks like it has a fair bit of rake. Icon looks to be well built parts.

 

Clean looking. Getting 35's of those KO2's put on in a couple of days. Any issues with them?

 

275/60/20 Ridgegrapplers on stock 20’s.Peace. D

 

Hey I'm days away from installing the same size wheels and exact same tires. What's your offset? Because the place installing them convinced me I needed a 25 offset or the tires would "stick out too much." Not sure if it's a little poke or they'd be way out there.

 

+25. They stick out just a little bit.

 

Got any pics of how it looks?

 

Parked at a weird angle kinda sloped

 

They don’t balance well at least not 37’s balanced them 9 times not perfect but good enough for now

 

20x9 Fuel Rebel 6's +20mm offset. On 35x12.5R20 Toyo Open Country A/T III's

 

Any poke at all on that? I was going to go with an 22x10 -18 offset but calcs say it would poke a lot. Ended up buying a 22x9.5” at +20 offset with a 305/45r22. Hope there is at least some poke, should be based on the numbers.

 

I'm kinda anal about tire/wheel weight and how it affects MPG. I believe the stock 20 set up ('23 Ltd w/265/60R20s) is about 68 lbs. ea. I calculated this by weighing stock wheels with snow tires I bought from TireRack (and they list weights with the specs of each item.) My snow tire set up weighed 87 lbs/ea. I found the weights of the snow tires (TireRack) and stock tires (Discount) and calculated what the stock set-up should weigh. I did this because the dealer I bought my truck from had installed Fuel wheels with over sized BFG KO3s and my mileage suffered (less than 15 MPG hwy.) I have more info if interested, PM me

 

I just had these Black Rhinos with Nitto Grapplers mounted. Truck came with a 2" lift from the dealer and Fuels with BFGs. That set up yielded less than 15 MPG so I found a lighter combo. I'm going for 18 MPG or better... Sorry about the full truck image -it's wide angle because I couldn't get back further

 

There's roughly a 1 to 1 1/4 inch poke. I had some Black Rhino Wheels 20x9.5 at -18 offset and the shop that did my work was concerned with potential rub using these wheels. Ultimately it wasn't the rub but the amount of poke with those that made me pivot to these +20mm offset wheels. Here's a pic of the poke with the -18mm at x9.5 wheel, where yours was X10, even more poke.

 

looks clean bro. What made you go with 35x11 vs 35x12? Any rubbing issues ?

 

very nice looking tundra bro. Ordered the wescott design pre collar lift kit. Do you happen to know the specs to align after the lift? And also how do you like the ride with the Toyo AT3s? I'm getting the same tires too. Any rubbing issue? Thanks

 

Thanks for that visual, very helpful. That wheel and tire combo looks good you installed. I ended up going with a Vossen wheel in bronze and AT3 tires. Been nervous and excited about the fitment since placing the order.

 

I agree 100%, truck looks super clean.

 

I was between black and bronze. Bronze will look good. Which Vossen wheel, they make some nice wheels.

 

Vossen HF6-4 in Terra Bronze. Using black Vossen lugs as well. 22x9.5