Torque Specs

Made some tables for torque Specs 2000-2003. Enjoy

 

..

 

This is much better than the one I made. Well done.
@Pinay can you add this one to the 1st gen info dump at some point. No rush.

 

Really good chart .BEST I'VE SEEN

 

Shit Stain? Wow...

 

Really shitty username. SHITTIEST I’VE SEEN

 

Anyone got the bed bolt torque specs?

Access cab. The six T55?

 

@TX-TRD1stGEN

Is "center bolt" for the pivot bolt on the upper control arm? Trying to find the torque spec.

 

It seems like it would be the center bolt, I was also thinking it could be the 72 , upper suspension arm to chassis frame

 

Yeah 72

 

Thanks. Torque from bolt or nut? Or whichever I can fit? From memory, torque wrench only fits on one side.

 

I think your always supposed to torque from the nut side, but I also think your right about only being able to fit on one side, that’s how the 4runner is. Besides a crows foot, just guesstimate, just get her tight, maybe check on it in a week

 

One of my passengers side seat x body bolts have worked loose. Figured I'd share my findings here.

 

Thanks this is very helpful!

I’m guess these also go Thur 2006 too?

 

Did you find out if they are good for 06 also?

 

Yes, it works for my 2005 based on the FSM.

 

did you ever find out torque for the bed bolts? I’m looking to replace a few of them. Thanks

 

This should be a sticky.

 

No, I didn't find anything first gen specific. I used the 2nd gen torque spec of I think 85 ft.lbs?

 

Best I can do is drop it in the 'so you just bought a 1GT eh?' sticky thread along with links to all the other important/pertinent docs I could find. So, if you ever need it, just open that sticky thread and it's right near the top.

​

 

According to the 00-03 Safety Recall (Special Service Campaign) – 90M and the 04-06 Limited Service Campaign(LSC) D0D, both mention 63ft/lb when re-installing the bed. They both use 90467-13076 for the bolts if needed.

00-03....Microsoft Word - 90M Dealer Letter Final 5.doc (carmd.com)

04-06....MC-10131878-9999.pdf (nhtsa.gov)

 

In a way it already is a sticky contained in the original Info Dump thread but no longer utilized or updated.

1st Gen Tundras Info Dump

1st Gen Tundras Info Dump | Toyota Tundra Forum

 

Little more i didn't find on here for 2005-2006.

 

These will show a broader view of the stuff on the front-end for the '05-'06 in case anyone needs it.

Note the legend in the bottom left corner so you don't over-torque anything:

​

 

I'm about to replace the broken driver side seat belt buckle in my brother's 2002 Tundra Limited Access Cab. This thread lists the torque specs for the seat mounting bolts. (Thanks, @Tundra2 !) Is there one for the bolt that holds the buckle to the seat? I downloaded the 2000-2003 Tundra FSM, but didn't see it there. I also ran a search of the 1st Gen Forum and it was not readily apparent.

 

Huh. I swore we talked about this pretty recently and decided almost anything seat belt related was 42Nm. The 2000-2003 FSM seems to indicate that in the specifications section.

​

 

Okay, so apparently I didn't know the correct term. I was searching the documents and forum for "buckle". (Couldn't find the facepalm emoji.)

 

Would be nice to see one for the 2.5 gen; the non 4x4 non TRD SR5s. Anyone out there have these?

 

The 2.5 gens would need to come together and produce it.

THIS! IS! FIRST GEN!!!
(Insert Leonidas meme here)

 

HA! Are memes banned now? I used to see that one all the time.