GEN 3 (2022+) Wheels and Tires Photo thread

I cut the rear crash bracket only and I have no rubbing so far. I've been off-roading but haven't done any rock-crawling. So, I cannot tell if I've technically "maxed out" the up-travel articulation yet.

A good alignment shop should be able to push your caster forward. What UCA's do you have?

 

I got an unrepairable flat on my front tire this week with less than 1,500 miles on them, so I decided to upgrade all four with a set of Toyo Open Country AT3s 275/65r20.

 

23' TRD Pro - Stock (before) - 35" BFG KO2 (after)

 

what's the tire and wheel set-up?

 

That's the exact swap I am thinking of doing. How is the ride with AT3 compared to stock tires?

 

The shop says they'd be a stiffer ride, but I really don't notice much of a difference. I am really happy with them so far. I wanted a little more height without a lift and it fills the space up nicely.

 

Vossen custom HF6-4, 20x9.5 +30, hub 95.1
Pirelli Scorpion Elect/RIV 275/65R20

 

Group, I have a question regarding lug nuts, apologies for the ignorance if this has already been stated [tried searching].

I have just bought a set of wheels from a company and I have no clue if I can use my existing lug nuts [2022 TRD OR - M14x15] or if I need to get a new set [60degree mag / flat seat lug hole length, etc.]. I have asked the distributer twice, no responses. Cannot get a number for the manufacturer to even call them. So a bit at a loss in terms of length and type I would need, if any, for these new wheels.

Any help would be great.

 

That looks like a TRD knock off so would think it would use stock lug nuts but not 100% sure. I can tell you that the stock lug nuts will not work with after market wheels but again those looking like TRD knock offs you may want to try and see if it fits. You would know immediately yea or nea! Good luck. Maybe someone else can give a more definitive answer.

 

Rolled the dice, assumed they would work! Yup, no problem. Thanks for the quick reply.

 

Looks good
Keeping the moustache silver?

 

What’s the company? eBay wheel?

 

Rolled the dice, assumed they would work! Yup, no problem. Thanks for the quick reply.

OEPlus is the Co.

 

Nope, mustache next.

 

Probably a bit more poke than what I was thinking but that probably is because of the rubber ?! Regardless, that’s going from an OEM +60 to a +15.

 

295/70 R18
2/1 Cornfed leveling kit.

 

truck looks great, what tonneau cover is that ?

 

Thanks! it's the diamondback HD.

 

285/60r20 BFG KO2s, no lift/level. Traded in an F-150 Tremor for this...ZERO REGRETS

 

What’s up guys, here’s my build out on Oahu. I got 17” Advans wrapped in 35x12.5x17. I installed the trd 3” lift as well. Minor wheel well modification but no cutting was done. Aloha

 

Servco installed the trd lift?

 

No, I took it to Mj motorsports

 

Love the Advans RGD2. I was considering advans in bronze metallic but they only have one size for bolt pattern 6x139.7 and it's too much poke for me with -10 offset. Would love to see it in a 18x9 and positive offset like +10. Love the concaveness of advans, way more then my Gramlights 57DRX. Advans are superlight at like 21lbs.

 

FN BFD are 18x9, +20, with correct hub size. Also just a hair over 22.5 lbs

 

Just looks like a rep of my gram lights but with correct bore size.

 

What does the center cap look like?

 

I don't know which came first, but the BFDs have been around since about 2013.

I don't honestly know. I inspected the wheels to make sure there were no visible flaws and then put them in storage. I won't be mounting tires on them until next Spring. I didn't even open the box with the center caps. If I can finagle it, I'll just reuse the Toyota center caps.