What have you done to your 2.5 gen Tundra today?

I got it from Overland Equipped. Another member on here told me to try them as he had one in his Tacoma. It shipped fast too. It's designed so that the screws don't interfere with the fuse markings on the inside of the lid. I bought my Blue Sea stuff from Amazon since it was cheaper than the marine store. Overland does sell it as well.

https://overlandequipped.com/collec...use-block-bracket-for-2007-2021-toyota-tundra

 

That's really nice. I might just get that too. I was going to try my hand at bending a bracket myself, so depends on how much i mess that up I have the same Blue Sea block you're using and i'm also adding winch disconnect.

 

I felt the exact same way. I bought one this past winter, used it for a few days and then took it out and returned it. Just not worth $300. If I want to have a touchy gas pedal, I can just push the tow/haul button.

 

Thanks. I saw Tundra234’s setup after I posted mine and thought that would have saved me a few days. That’s a nice looking set up. I love mine but it took a few days to build. Working with stainless can be a pain in the ass. I got my BlueSea hardware off Amazon also. I built a tray for mine today and got it permanently mounted. Love how it turned out and I love that I can remove the fuse cover box without having to take anything loose. Now I need to buy more lights.

 

Yea I had platisipped my Tacoma rear number when I had it. Lasted me over 4 years before I could see any chrome through it. But of course that was the back of the truck. I’d be really curious to see how long you ca go on the front with the dip and bed liner!

dip is easy to remove, ever try to take anything like yours off? Or touch it up?

 

I think it’s the angle of the pic. It still has a very slight rake to it but not much. If you look at the top pick it looks pretty level.

 

If this is still available im interested

 

It's not the full kit as pictured. Just the 3 knobs and I purchased them from him.

 

Just rolled over to my 3yr lease mileage limit with 14 days to go. With the new leasing so high, decided to buy it out and keep it for quite some time.

Now time to buy new tires, rotors/pads, and get an alignment.

 

I'm normally not a fan of red trucks, but that color is bada$$!!!!

 

Thanks!

 

Those look like Rock Warrior wheels. If so, are you running spacers? Like others have said, looks awesome!!

 

Yes they’re RW wheels and yea running 1.75” BORA spacers, I’m around a +5.5offset with them. Thanks!

 

thanks for the support and checking out the videos!…hope you’re liking them!

 

After 5 days of rain, went to wipe down my truck, only to find a screw in the right rear tire. I was going to have my son take it to his shop to fix since the screw is in the center of the tread, but then I remembered I had the Tire and wheel warranty with Toyota. Pulled the PRO wheel/tire off the truck and put on the oem TRD OR wheel/tire real quick and then took it to my local dealer. The dealer won’t fix the tire under the warranty I have. They will only replace it which is fine with me. My only concern is that the rest of the tires will have slightly less tread. Thinking of pulling the spare and swapping it so I have 2 new tires, thoughts? I did confirm the warranty has no limit. The advisor said I could have 100 tires replaced and never pay out of pocket,(as long as there’s at least 3/32 and not damaged due to being under inflated) I didn’t take the time yet to check my other 3 tires to see if they have a screw too.

Hopefully they don’t damage the PRO wheel and balance it correctly. Took detailed pictures of the both sides of the wheel before I left it with them.

 

$7 plug kit at the auto parts store plus about 10 minutes. Unless you need an air compressor too…. Then it’ll be a little more. What better time to invest?

 

I could have gone that route, but why not use my warranty and get a new tire?

 

It's a conspiracy. I had to go back to the office this evening because I forgot something that couldn't wait until tomorrow. About 1/4 mile before I turned in, I heard the all-too-familiar bump bump bump that indicated something was in one of my tires. I drove into the plant, parked, and saw 1/2 inch of a screw sticking out. The tire wasn't noticeably losing air but I didn't want to risk the 25 minute drive home with it in there, so I changed it. Dang that sucks!

 

Joined the dash pad geezer club today

 

How are they attached...if they are. If not, I'm curious if driving down the highway the wind will make it shift and move around.

 

Velcro

 

Are there any benefits to a dash pad, I’m just curious, because I do kind of like the look.

 

Prevent dash glare and dash protection if you park in the sun primarily.

 

x2

I use dash protectant but wanted to try this. Especially since we are big on sun here

 

I’m going this route instead of using my weather tech sun shade. More convenient and still looks good.

 

I think that looks awesome. Now you got me thinking...I have the Rago modular dash mount. Wonder if I got this pad, if I could cut the fabric to accommodate the dash mount mounting holes, then put the dash mount on top of the pad. The pad fabric would then minimize the gaps between the dash mount and the dash that exist now, and also provide extra securement points for the pad other than the velcro...

 

Same here. I use 303. Not to jack the thread, but I saw a cool decal the other day. "Get off my ass or I'll deploy your airbag".

 

They're completely customizable that way. In fact the instructions say that if there's a sensor they didn't cut for, take some sharp scissors and get to cuttin

 

Thanks! What fabric did you buy?