GEN 3 (2022+) Wheels and Tires Photo thread

What is bizarre is I checked with a tire shop here and they were telling me that the KO2's in 285/70R18's are the same weight as the Duratrac's 295/65R18's. I realize I will take a knock or two on the mpg, but that is crazy to me that a larger tire is lighter than a smaller tire that are both E rated...and have 3/32's more tread. What am I missing? Density of the rubber BFG's use over Goodyear?

 

Any rubbing whatsoever on your setup?

 

Been through both 3rd gen tire threads and haven't seen anyone running a +12 offset ?
Looking to add a set of Black Rhino Bantams with the 295/70/18 BFG KO2. Ive seen a lot of guys with 35x12.5 and a +18 offset with a little poke but was wondering if i ran these 11.6" tires with the +12 offset if it would still poke a little...

 

As you get closer to 0 the poke gets greater...but a +6 differential is so minor that it will look VERY similar to +18s, maybe a 1/4" more poke

 

Easiest way for me to determine the poke is to do MM to inches conversion then i pull out my stick ruler and go on from there

 

Black Rhino Rapids in +12 here…295/70/18’s

You will get poke alright…just a little more than the +18’s

 

That's not too much poke...looks really good !
Are you running any level or lift with them ?

 

Yup…Westcott 3/1 lift

 

this is a +7

 

I love the look of that stance...

 

Hard to tell from pics...if you had to guess how much poke do you think that is with the +12 ? 1" ?

 

2:49
https://youtu.be/vTaqSgzzt3Q

 

I really dig the black mustache vs wrapping it to match the body color. Assuming the Toyota body parts are in this same black finish, this is the way I'm gonna go (eventually).

 

Someone needs to buy the new Method 706.

https://www.methodracewheels.com

 

Hello Tundra community members!

 

Wow, w/the LIFT and tires it really makes the truck look like a truck now..Beautiful!

 

I had them on my Tacoma and really liked them...

 

Looks good, what are those HRE rims? Looks expensive!!

 

HRE flow form FT1 if anyone is interested, 20x9, 0 offset. Contacted HRE and they had no specs on the car but everything from the previous Tacoma specs fit.

 

35X12.5X20 Mickey Thompson Baja Boss A/T on stock trd wheels with wescott 3/1 lift.

 

Nice! What are the specs for the battle born rims?

 

Does anyone run the Hankook Dynapro AT2's?

 

That Blueprint color really tricks the eyes depending on the lighting and angles.

With the 12.5 wide tire are you free and clear from any rubbing?

Upper Control arm rubbing with true 35’s I thought/heard could be an issue with the stock 20’s if you didn’t run a spacer/shim hence the question.

 

Just about yes…depending on how the suspension is loaded however (like the incline and slanted driveway I have) it can appear more on one side and less on the other.

…but flat surface it’s about 1”

 

There is no rubbing. I was prepared to use the 1/4" spacers but didn't need them. Didn't even need to pin the fender liners back. I'm guessing it must be the tire I used.

 

Oh ok…very nice

 

18x9 +18

 

Beautiful truck

 

1.75 rough country n airbag readjusted up 1 inch

 

How has everyone’s experience with the Rough Country 1.75 been?

Have a local shop running a deal right now where they are doing a free rough country level kit (& install) with the purchase of a wheel/tire combo.