What have you done to your 2nd Gen Sequoia today?

Yep that’s the one I’m putting on with that same tire size. Not sure what brand of tire yet……..

 

Those TRD PROS are really nice!
I have Bilstein 5100s & 1.75 Dobinsons all around, looking for rims & tires now.

 

Do you remember what you spent to get the westcott installed

 

Installing myself……..

 

Found 1 bad front caliper on the wife’s 08 sequoia with 250k miles this week. Several others had badly torn seals or were missing chunks.

I ordered 4 brand new not RE manufactured calipers,rotors,pads,and stainless steel lines plus a pressure bleeder pump kit and adapter.

Looks like I’ll be building her a new car haha

 

Where did you get the below parts from and do you have pictures to share??


TRD cup holder coasters
TRD seatbelt pads
TRD radiator cap and oil cap
TRD pro Battery tie-down

 

I’m picking up the truck from detail shop. tomorrow morning. I will post pics soon after.

coasters, pads, radiator and oil caps all came from Amazon or eBay.
TRD Pro batt tiedown came from A guy who custom makes them on the Tacomaword forums. I will try to get his contact info………

 

Haven’t done much to ours lately, other than keeping it clean.

 

Rear springs are a nightmare. I bought three compressors, all were a pita, Farnsrocket found one that seemed better.

https://www.eastwood.com/eastwood-m...kedid=546239690373&wickedsource=google&wv=3.1

 

Here is the link for the battery tie down guy


https://www.tundras.com/threads/fs-battery-hold-down-bracket-by-coupe.9946/

 

I have bought two of them, quickly shipped & very high quality.

 

I got a 27f AGM Northstar clone from Batteries+ for less than the group buy a few years ago.



Also, got the last three pieces to be fully OEM on the transmission cooler. Going to install it, and might do the trans filter sooner than I had planned.




Figured out a solution to my jack stowage.

 

Did the front brake SS Lines,rotors,new calipers,and sway bar end links

The rears will come tomorrow and later this week

 

Here’s the link to my mods page if anyone is feelin like visitin………..

https://www.tundras.com/threads/2021-sequoia-trd-pro…-here-comes-the-mods.98236/#post-2501177


Gonna post all my future pics of my mods on there.

 

Got my ‘winter blend’ ready to go. Delo SDE 15w40 will be a little too thick in the upcoming months.

 

When it's 125 here I have to remember it's never under 45.

 

Pure, organic, non-GMO Castrol GTX 20w50 is your friend

 

I have always used Castrol 0-20 SYN. Buy it in bulk, running low, only have 15 quarts.

 

Decided to send the current sub 5k oil to Blackstone, (take a small sample) then run a flush & use a change of Amsoil, over the weekend.

 

Ordered an HP Tuner MPVi2+ to get a tune.

It will look great with my Orange Virus and EcuTek tuners.

https://www.hptuners.com/mpvi2plus/

 

i had a buddy do it for me. its not a hard job if u got the right tools for it

 

I feel your pain, I had to wait for summer to end to tackle mods, 115++ is no fun.

 

The insanity is real, just ordered the same Doug Thorley headers I have on the Tundra.

 

The last time I had a Doug Thorley headers was for my 75' Celica 35 years ago. LOL! Great find!

 

They really opened up the torque on the Tundra.

 

Hauled back to South Dakota 24 cases of carbonated water from the nearest Trader Joe’s. This is the first real use for my Air Lift airbags - had them inflated to 20 psi and that almost eliminated the squat.

 

2016 Sequoia, was OEM until a few month as ago. Remote start next week.

 

Nice, I’ll be going with a similar setup on the IMS. How do you like them and what size springs did go with?