What have you done to your 2.5 gen Tundra today?

Definitely interested if you find a way to run the flood light from a switch.

 

Finally got my CBI mounted.
Thanks to the current world of backorders and extended manufacturing times, I’m not completely done.
Still have lights to add and haven’t made up my mind which lights to use under the Baja bar.
Adding running lights in the sensor holes.

May be different but it’s mine.
That’s what wanted.

Added a piece of sheet metal behind the CBI cutout to make it more visible.
It’s off of an old tailgate I had to replace.

And yes, my truck is sticking it’s tongue out at you.
Waiting on my Agency6 shackle.

 

Yea I’m not gonna push it, especially cause I have the custom “puddle lights” under truck that come on at same time...we’ll see what happens!

I think that may be what I actually do...I’ll know better once they get here tomorrow but thanks to our man Casey for the idea!

 

I just got my new switch. I intend to use this as a master power switch for the Switch Pros 9100 setup that arrived a few days ago and is pending install, so that I can have the whole system shut off when I want to. If I can't use it as I intended, then I'll find another use for it.

 

Where did you get it?

 

It's a CH4X4 switch (Cruiser Heads 4X4) I ordered mine from Amazon but you can source them from other places as well including direct from CH4X4.

 

Cool. I’ve ordered from them before. I was just curious because the printing (? Etching?) is very clean. But it makes sense it was them, they do great work on the custom stuff. Thanks!

 

Yep, I have used their products in the past. I like them. You are very welcome.

 

I don't know how much juice the actual Switch Pro unit pulls - as long as your running the actual power through an appropriately-sized relay, you should be GTG.

 

That's how I ran mine Robert
https://www.tundras.com/threads/caseys-2021-lunar-rock-trd-pro-build.77317/page-10#post-2163301

 

Installed a riGd ultraswing with frontrunner fold down camp table to go with the Decked system. Eventually when i get a lift/wheels/tires ill put the full size spare on the ultraswing also.

 

Yeah, If I can just shutoff the switch panel itself, I will do so. if I need to shutoff the underhood portion, I will use a properly rated relay setup.

 

Only issue I've had with the CH4x4 switches is they are a darker/brighter blue than all the factory stuff. But, then, the "light blue" AOB brand ones don't quite match factory either.

 

Yep, I was aware of that issue, but they seem better than the alternatives I have seen so far. Plus I dig the Teq logo.

 

How did you get it to hover above your hand like that?

 

I've got the magic touch.

 

Can you provide any details on your bike holder, did you make it custom? That could be a good product.

 

Any more progress on this? I wanted to do something similar just for some flat storage in the back.

 

New decals my pride. My Bucs,My Daughter’s Soccer team and my Supra..... lol

 

New Tires. Replaced the stockers back in June last year with Cooper XLTs. I think the Cooper XLTs are great tires but I got a bad batch. One had a sidewall crack and was replaced but they never would keep balance. Put 9000 miles on them, balanced 4 times and they just were not right so the last time I went in DT said they would give me full credit for them towards something else. Decided on Falken Wildpeak and just got those installed this morning. They feel better and balance seems good, time will tell. The Falkens are 6 lbs heavier per tire, which is noticeable. They seem more heavy duty and have really deep tread vs the Coopers. The Wildpeaks are Very quiet. They are also about 2-3 tenths taller, wider than the Coopers, noticeable with the eye. Lets hope they keep balance and wear well.

 

Got 2 yards of mulch today for our landscaping. Made two trips.

 

How did you wire up your LED'S to come on when you unlock your truck or open the door?

 

You can tie into the driver foot well light. At least, that's what I did and it's working well.

 

I did make it custom. burned out of 11GA steel and broke at 90 degree angle at the bottom.
Used it on my 27.5" bike and it worked with my 29" bike now as well. Pretty simple.

 

Here's another picture I just took.

20210401_163219 by Robert Stewart, on Flickr

 

Just installed the Pedal Commander.... Wow. May need to upgrade the brakes.

 

So fresh and so clean...all that pollen had to go. Installed some door sill stickers also.

 

So you can fit a 29er in your CM without removing the wheel using that? If so, I'd buy that for sure if someone sold those mounts.

 

Blacked out the rest of the steering wheel. What a difference!

 

Well done!