6112 Setting and Tire/Wheel Combo Thread.

The top setting gave my truck exactly 3.30" and has settled down to 3.25". I installed some @BOSS4x4s shackles set at 1.50" in the rear for a leveled look. I also had some SPC UCAs installed and the alignment is great. No issues at all.

 

I put icon 2.5” piggy back on the rear. And they work so good it makes the bilstiens feel like a cheap toy if I’m being honest

 

stock tire size the Michellin Ltx At2

 

Got any pics of your truck? Sounds like the exact setup I’d like.

 

There are a few pictures in my profile for you to look at as well.

 

looks badass man. Exactly the look I’m going for.

 

I’m about to put this setup on, I’ve noticed a lot of you did 1.9 with a CB shim on both sides (or 2 driver one passenger). Does that ride better than top circlip setting?

 

There is always a debate. I did the 1.9 setting with 2 drivers and one passenger....can't compare the ride but after talked to Darren from Boss Offroad...that was my choice. Still rides a bit stiffer than stock to me but...only been about 100 miles.

 

RollTide82: how much of a lift did you get initially and how much did it settle? Is the passenger side level to the driver’s side?
Thank you in advance

 

If I go with 6112’s up front (set on 1.3 because I tow a camper) do I need to replace the rears? I have TRD shocks stock. I just want to go up to 275-70-18’s.

 

Great looking truck!! Any other photos?

 

Thank you.

 

275/70-18s fit perfect on a stock truck, no lift or changes needed. So if your springs/shocks are in good shape no need to spend the $, just buy the tires you want and enjoy.

 

I'm looking to do this setup on my 2008 5.7v8 Crewmax.

What is the CB shim and where do I get it? Will I need it pre-assembled onto the strut coil setup or does it bolt on during installation?

 

Shim bolts on during installation

 

Just scrolled through a lot of this thread and didn't see any first gens on 6112s... Is there a reason for that? I've been looking at them for my '05, but was wondering if there's an alternative everybody else uses.

 

I've seen a few. Not to many

 

I’ve had 5100 on my Tacoma’s and went with a rancho quick lift /adjustable ride on my 04. I was happy with them. Rode really nice. I didn’t really know about the 6112’s then, But I just ordered some for my ‘17 Tundra.
https://www.4wheelparts.com/p/2004-Toyota-Tundra-RanchoRancho-2.25-Inch-Loaded-QuickLIFT-RS999923/_/R-BCKM-RS999923?ppcfon=1&gp=1&ef_id=EAIaIQobChMI4t-qwIas7QIVOCCtBh1djQPxEAQYAiABEgL_q_D_BwE:G:s&s_kwcid=AL!7836!3!430284196272!!!g!671659370080!&gclid=EAIaIQobChMI4t-qwIas7QIVOCCtBh1djQPxEAQYAiABEgL_q_D_BwE

 

Made it through all 48 pages.... all the trucks look fantastic and I believe 6112s are the route I want to go for my '21 Crewmax Limited 4x4. I ran the Eibach kit on my Taco when I had it and love the look of a leveled/lifted truck. I've read about diff drops, CB drops, Coachbuilder shims, etc. and am not sure what all I might "need" for the limited lifting that I want to do. I'd like to run a 275/65R20 (34x10.8) and am wondering if I can get away with this at the 1.9" setting. Hate to even ask this since I'm used to doing a lot of the work myself but is having Toyota install the parts one way to avoid warranty claim denials in the future?

 

You should post in new member intros and show us your truck! That's a good question that I don't have an answer for. I also doubt your dealer will install an aftermarket lift. If you worry about warranty, you might be better off having a different shop that does aftermarket work, install your lift since most of those places warranty their work. Yes it's not the same as your Toyota warranty but it might cover you for your basic issues.

 

I appreciate the response, and to clarify I would not expect Toyota to warranty the aftermarket part, I am more concerned with things they would claim were caused by the installed part whether they were or not (simple example: a leaky cv boot).

 

Installed my 6112 at top setting with coachbuilder +2 shackles and bilstein 5160 on Sunday and got my new tires today. Didn’t get the tires I was planning on but when a good deal comes up you can’t pass it up. Got Toyo R/T 35/12.5/18 and they are a great fit and make the truck look like it should.
Will try to get some better pictures tomorrow in the sunlight. But very happy with the results of lift with 35s

 

Definitely need more pics. Looks nice, well done....well except it's a slow color. Gotta have that MGM

 

Yes, more pictures are needed. was busy with this Stupid thing called work today that really gets in the way of other stuff... with the exception of funding the other stuff.
I thought super white was the faster color. It says it’s super in the color.

 

Here are the pics my tire guy sent me when he finished the install.

 

Pretty much solidified my decision between 295/70R18 or 35s. That looks great!

What about trimming/rubbing??

 

When I first picked up my truck it barely rubbed at full lock in reverse. Then had it aligned and now there is something barely rubbing at full lock in drive. Rims are +18 offset and I have the coachbuilder bumper shims
I did pull my front fender well plastic down before dropping it off so I’ll see if I can fit that back in hopefully tomorrow

 

Hello, nice truck. I have a 3” spacer and want to swap to Bilstein 6112. Is your truck 4x4??

 

Thank you if you are talking to me and yes mine is 4x4. If you want to keep your 3” you’ll need to get some cb shims.