Will 285/75 rub on bilstein top setting

I feel like I have spent hours reading threads on wheel and size and tires, and seen multiple opinions saying they will or won't rub, still just as confused as when I started lol.
I have a set of icon six speed sitting in my cart( Keep changing my mind on the color)
And in the process of picking a tire, I know a 285/70r17 will fit, but would a 285/75r17 fit without rubbing? All I have is front bilstein 5100 top setting. I'm fine with removing mud flaps. If anyone has a 2nd Gen with same set up including wheels, any advice? Will the 285/75 be noticable difference for the 70.

 

So you're wheel offset will make a difference. Not sure if you're running stock? 14 wides with -77 offset? 9 wides with 0 offset? Have you looked over this one yet? https://www.tundras.com/threads/largest-tire-you-can-run-stock-for-all-generations.9762/

 

The wheels I'm getting are an inch less in diameter (17") compared to stock (18") offset 25mm. 5.75 backspace

 

I had some 275/60R20(33/10.8R20) on +20 offset 20x9 wheels that would rub at full lock in reverse on a set of pro comp pro runner ss struts at leveled setup (2.5" lift i believe). thats pretty close to what you're looking at with. With the 285/75 being 33.8/11.2, i feel like with that offset/diameter/width you would rub just a lil bit. not extreme, but feel you may need to trim/mold some plastic liner

 

Thank you for the info. Might just be safe and go with the 285/70s. Dont really go off road other than hoping a few curbs to go fishing but prefer to have clearance without rubbing issues

 

I doubt the 285/70 is going to rub, but I do think it will look way to small with a lift on your truck. If those two are my only choices I'd go 285/75

 

I just have a front level so not really much of a lift. I definitely think the 75 would look better but havnt found any to comment if they have that wheel/tire level combo yet. This pic is a 285/70r17

 

Youll be fine with that offset and backspace, be cautioned however, i did the same and ended up stepping up to 35’s,

 

Thanks. With the 75s or 70s?

 

@Bailey was running 285/75r17 I believe and think he was around 2.5" lift

 

Other than removing mud flaps, nothing rubbed?

 

Not sure, hes got a full build thread on his truck. If you go to his profile and click on his posts itll pull up

 

Thank you, I missed the Bailey tag. I'll check it out

 

I’ve got 285/75/17s and I had some rubbing on the front wheel well covers, the plastic lining. Trimmed that up and I was good to go. I have 6112s up front at 1.9. I don’t know my rim off set, but my tires stick out about 1.5 inches from the fender. Not sure if that helps ease rubbing issues or makes them worse.

I like the tire size but sometimes wish I had gone wider.

 

What wheels do you have, I could probably look up the offset

 

That’d be cool! A buddy’s dad owns a shop and I gave him a list of what I wanted and he did the rest. We never really talked about off set. They are Method Grid wheels, 17s. Like I said, the wheels stick out about 1-2 inches from the side of the truck if that helps. Thanks!

 

https://www.tundras.com/threads/icon-17-six-speed-wheels-picture-thread.13248/
good info here. I think if you end up lifted 2” and are willing to do some rearranging in the fender well the 285/75r17 should be about the perfect match. Also note that Nitto RG and Cooper ST Maxx may measure larger than Falken or BFG.

 

Good to know. Was leaning falken or toyo open country

 

Looks like those wheels are 18 offset with 5.75" backspace

 

I’m running icons with 285/70/17 no lift, no trimming. Slight rub reverse full lock.