What have you done to your 2.5 gen Tundra today?

The sway bar will be fine...Had the 6112s before the ICON 3.0 coil overs

 

Super sickness. I got my ditch lights installed today. I was nonplussed about the literal rat's nest on top of my engine.

 

Sounds like a good idea. Do they pull out easily? I’ll have to look again tomorrow.

 

They pull out easy from the bottom.

Be aware, if you ever want install them, that job is a pain.

 

Whole bunch of TWSS in there

 

Yes, yes there is.

Thanks for noticing...

 

That’s what I thought. I may just leave them in that case. Thanks.

 

Those sensors are annoying... I just accept in time it will be on lol

Goals man!! She's just getting broke in!! I have a 14 too with 103k on her, she's just starting to get broke in

 

Got pulled over again by the same cop who told me I had "obstructed safety equipment" this time so he could tell me to take the license plate off the bumper and put it on the camper. I couldn't help but ask "are you following me? And why didn't you say this last week when you being a douche about brake lights?"
He didn't have an answer, only an attitude.

 

Started getting FB ads after I joined a couple Milwaukee pages for expensive custom Packout bed plates. So I thought thanks for the idea, I need more reasons for buying Milwaukee stuff for home not just at work. Picked up some Amazon rail mount nut things and a wall plate at Home Depot. The wall plate Needed just a tiny bit of retro fitting to the mounting holes because of thread size. Came out perfect. I have two swing cases so I was limited to placement but I am sure the small wall plate can mount right inside the tailgate.

 

I'm a big Milwaukee fan but I'm also cheap lol. A contractor at work threw out a bunch of empty Dewalt cases, seen to the right in this picture. One holds my compressor, one holds the hose and air tools, and one holds random straps and bungee cords. I like the packout board though. Might have to look into it. I just got a factory bed divider, so I've got some reworking to do on my bed carry. I want to try to mount the shovel and possibly the traction boards to it.

 

Thank you for the use of "de-chrome” and not the Millennial-Zoomer irritating “chrome delete” lingo...

 

Nice chrome delete

 

This is the current way I have it set up. Most of my gear (come alongs, big straps and some larger tools) are in the blue clamshell, and like I said above, the compressor, air hose and tools, and small straps are in the Dewalt cases. I just picked up this OEM bed divider. Previously everything was held in by that ratchet bed bar at the bottom, and hopes and prayers. I’m going to leave the bed bar for now to help the divider out.

 

Cleaned up the wires to the amp under the passengers seat after I installed a new headunit!

 

Hit a milestone today. I’ve only read about it and now I’ve experienced it! Let me tell you, it feels great.

BOOBS

 

Added a couple Baja pods to the back.

 

Any issues with my passenger's side ditch light wiring being routed like this? I admit I do not know what those black hardlines are for. I will get it more taught (and cut the excess ziptie) it y'all give it the greenlight.

 

what head unit did you go with ?

 

I got some of those wire routing loops, and used the plastic nuts holding the felt liner for the cowl, right above where you have yours on the brake line. I don't think there'd be any issue with it though.

 

Had to be someone in this crowd. DUMB

 

You should be fine, those are ABS module lines

 

Thanks guys!

 

Installed Tech12Volts amp and woofer upgrade along with VLED interior lights. Both very straight forward, thank God ! LOL

 

Hauled a few ducks home from the blind today.

 

And….now you have a problem…

Someone will have to eat them …

 

Haha planning on cooking them Monday night. Will be the wife’s first time trying duck so curious about what she’ll think.