What have you done to your 2.5 gen Tundra today?

Depends which Sumo - https://www.superspringsinternational.com/shop/ssr-610-47/#additional-info

 

I did order the 610-47 but doubt they’re almost 11” long. Especially looking at all the install pics. That might be the shipping box dimensions… maybe.

 

If it helps, I just went out and measured mine (black) - 5 3/4" tall with a gap of about 1 1/2" to frame above.

 

Exactly what I needed. Thank a lot!

I’ll measure my gap tomorrow with the OME leaf pack and will start printing a spacer.

 

Installed the 1 Touch Auto up/down controls on all four doors. Super easy to do and took about 15 minutes total. No issues at all. What an awesome mod. I got the white light.

https://cartrimhome.com/Window-Switch-Automatic-Lift-Function-for-Toyota-TUNDRA-2007-2021-DA

 

Added a remote start this morning. Took less then an hour start to finish.

 

Thank you

 

Doing the Powerstop Z36 upgrade (caliper, pads and rotor). After doing the recommended break-in, I definitely feel a difference. Outgoing pads were not overly worn despite having 52k on them.

Discovered the need to proactively replace both front hub assy so I only got front end done yesterday. Went ahead and ordered new front dust shields since I'll be taking that apart anyway and they are ready to split apart (101k miles in central NY). Damn the rear dust shields are expensive - looks like part of the parking brake assy? I may not touch those - the rears are not terribly rusted.

Anyone else surprised at how clean their brake fluid was at 100k? Never changed, system integrity never broken before this caliper replacement.

Gonna add the PowerStop SS brake hose kit once I figure out how to break the rusted fittings apart.

 

Looks Great! I have an RCI setup as well. I added the tranny skid and recently attached their cat guard kit as well.

 

Just the front. Didn't want to deal with the wiring.

 

$170 Fitcamx 4K Dash Cam Suitable for Toyota Tundra 2017-2021 & Sequoia 2017-2022 Limited SR5 Platinum TRD Pro, Integrated OEM Look, High Definition 2160P Video WiFi, G-Sensor, Loop Recording, 64GB Card

https://www.amazon.com/gp/aw/d/B09Q8WB6S6?ref=ppx_pop_mob_b_asin_title

 

Yeah it was the one linked, it shows the picture of the new Tundra but it's for the 2.5 gen.

 

This is

 

I can't quite tell from the angles here but are the tow hooks outside of the side framing; or is that a passthrough cut into each side of the plate? Asking because I have a plow mount.

 

where did you get that battery tie down?

 

"This is.....rust.

 

https://www.tundras.com/threads/fs-battery-hold-down-bracket-by-coupe.9946/#post-162916

 

The colors look better in real life. The gloss white looks so good with my super white Tundra.

 

Installed Fumoto valve, wheelers bump stops, SumoSprings and changed engine oil. Busy day.

 

You’ll have to let me know if you like the fumoto valve. I’ve been on the fence about getting one. I’m concerned that when I bottom out the safety piece will come undone and the lever will release all of my oil.

 

The lever has to be pressed and rotated about 1/4 turn. You could always get a Valvomax as an alternate.

 

You keep that thing clean!

 

Will do. I have one on the 4runner as well. I’m tired of oil splashing everywhere

 

Thanks

 

What springs do you have and how do you like them?

 

OME. I like them a lot. Ride isn’t too harsh and it raised the rear about 2.5” with the canopy. I had them on my previous truck and put 80k+ miles and no issues at all.

 

Do you have to be connected to a wifi network it creates to access clips? I run Wireless CarPlay & I feel like that won’t work. The English translation on their Amazon FAQs is terrible.

 

I designed a little bracket out of stainless steel for a rearward facing light that I tied into the cargo/puddle light circuit. I already had wiring in a junction box back there so it was really easy to install tonight. Just a fun little project to give me a little light when I'm loading mountain bikes on the hitch rack in the dark

 

Finally installed my spider no drill roof rack I got from my dude @reywcms several months ago. Loving it!
I have more stuff playing around I need to install: frac harness and camera, vled footwell lights front and rear, and an esp rear seat under storage unit.

 

Got my Tech12Volt JBL DSP amp installed.
Finished the core of my wiring distribution setup.
Got most of my ARB twin compressor installed.




Still need to run the wiring for compressor power (need longer cables), Switch Pro controller, and the switch for the winch power supply - all of which will come through the drivers side firewall.