1. Welcome to Tundras.com!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all Tundra discussion topics
    • Transfer over your build thread from a different forum to this one
    • Communicate privately with other Tundra owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

Looking for Wheel Bearing Recommendations

Discussion in 'Wheels & Tires' started by dbb1776, Jun 18, 2025.

  1. Jun 18, 2025 at 7:31 AM
    #1
    dbb1776

    dbb1776 [OP] New Member

    Joined:
    Jun 18, 2025
    Member:
    #136667
    Messages:
    2
    2017 SR5 4x4, just rolled over 200,00 miles. All my lights are lit up, 4wd hi/lo, brake controller, etc. 99 percent positive it's wheel bearings due to age, use, and noise. Original bearings. I can replace the front ones. Pretty sure I can get the back axles off and have the rear bearings swapped at a shop.

    BUT: I'm having info overload when it comes to balancing quality and price.

    On the front, I want a complete quality front wheel bearing assembly. I'm looking at parts stores and bluepit bearings. Looking for OEM or better quality.

    On the rear, should I buy OEM or is there a quality after market bearings available? A complete rear axle ready to go would be great, but all i see is Dorman brand.

    I'm located near Huntsville and Bryan Texas if anyone has any shops they like in the area.
     
  2. Jun 18, 2025 at 7:36 AM
    #2
    joseph_womack

    joseph_womack @ 4x4bound

    Joined:
    Nov 3, 2020
    Member:
    #54467
    Messages:
    1,091
    Gender:
    Male
    First Name:
    Joe
    Louisiana
    Vehicle:
    2007 RCLB, 4WD, 4.7L V8
    3/1 Lift, 35s, Front Bumper, etc etc
    I ran a duralast gold hub in the front and it failed probably after 2 years; I’ve been running a NAPA branded one and it’s been good

    Timken is what you want for bearings; but see what codes are stored in the computer and actually determine which bearing is bad before just replacing them all. It was probably water intrusion or dirt that ruined the bearing and the others are most likely fine (check each obviously)

    you can get an automotive stethoscope and put it on the hub and spin the wheel to determine which is grinding (or just that truck up and let the rears idle to hear it)

    and welcome to the forum!
     
  3. Jun 18, 2025 at 10:22 AM
    #3
    dbb1776

    dbb1776 [OP] New Member

    Joined:
    Jun 18, 2025
    Member:
    #136667
    Messages:
    2
    I saw NAPA had some decent looking front hub assemblies. Can I see the bearing info on the assembly? I live on 8 miles of rough road. Rain means likely water crossings. Nasty when wet, dusty when dry.
     
    OldGuy03 likes this.
  4. Jun 18, 2025 at 10:33 AM
    #4
    OldGuy03

    OldGuy03 Still new here, but working on it

    Joined:
    Apr 25, 2023
    Member:
    #96046
    Messages:
    14,424
    Gender:
    Male
    First Name:
    Jay
    CO
    Vehicle:
    12 MGM DC RW
    I replaced with oem, which I sourced from Fred Anderson Toyota. Timken is the best bearing you can buy if want want to upgrade. But 200k on oem should tell you that's a quality part. I do not recommend the Dorman complete hub assembly as it's low grade at best.
     
    Last edited: Jun 18, 2025
    joseph_womack likes this.
  5. Jun 18, 2025 at 10:38 AM
    #5
    KNABORES

    KNABORES Sarcasm incoming

    Joined:
    Jan 1, 2020
    Member:
    #40572
    Messages:
    14,397
    Gender:
    Male
    Arkansas
    Vehicle:
    2000 Limited TRD AC 4X4 Thunder Grey 278k miles. *SOLD* 2019 Limited TRD CM 4x4
    Bilstein 5100's on the forbidden notch Husky HD rear leafs 16x8 Eagle Alloy 187's with 285/75/16 MagnaFlow 3" flow through Pioneer touchscreen with backup camera Full interior and dash LED conversion Trailer brake controller with 7 pin Bedliner coat bumpers & trim ARE Mpulse topper - Rhino Vortex rack
    SKF and Koyo were some original Toyota bearing providers. Timken quality has slipped a bit over the years, but they were the go to forever. I think they got purchased by one of the above brands.
     
    joseph_womack and OldGuy03 like this.

Products Discussed in

To Top