What have you done to your 2.5 gen Tundra today?

Yes, heavy duty Velcro tape.

Yes they sprayed the bolts and two of the from tie down holds but not the rear. Weird

 

Finally got to show mine off to another tundras.com member. That was kinda cool.

 

3rd brake light with strobe

$12 Syneticusa 2X T10 921 912 60W Red Flash Strobe LED 3RD Brake High Mount Stop High Power Light Bulbs

https://www.amazon.com/gp/product/B07CZ2DGQ3/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1

 

do they work well? mixed Amazon reviews

 

working so far!

 

Washed em both!!

 

Crappy pic, but had the Revtek kit and BFGs installed today. Sits great completely changed the looks and stance
2.5/1.25 and 275/65s on the factory 20s for now. Only had to tweak the skid plate, front flaps still on. No rubbing. Rides great!!

 

that extra inch of tire and aggresive look is a perfect IMO.

 

Really like my bedrug, but after a couple years, the strips on mine came off. The bedrug almost flew off driving down the highway, too. Have a bar in the bed to weigh it down now.

 

I have a tunneau cover .. i don't think that will happen to me but they do sell velcro strips at HD or Amazon that might work if you need replacements.

 

This was yesterday but enjoying it today, especially when things are not rolling around.

 

Instead of buying an expensive Platinum lid, I bought a synthetic leather console cover on ebay, padded it with foam (not shown), and installed it like a Katzkin.

 

$55 LASFIT 7440 LED Bulb Anti Hyper Flash Canbus 7443 Front or Rear Turn Signal Light 7444na 7441 7444 7440NA W21W WY21W Bulbs No Load Resistor Need, Upgraded Amber (Pack of 2)

https://www.amazon.com/dp/B07CMSD8CS

LOLZ

 

Loncky leather steering wheel cover?

 

Sweet Jesus these are enormous... will install Saturday

 

Genuine Tacoma leather wheel, it fits (only the wheel, not the Taco controllers, use all existing Tundra hardware)

 

Cquartz Dlux on these before install. I also polished/coated my bulge and surround to allow time to dry before installing.

 

I don't know if this counts... but I didn't know I had the power roll down window. Not kidding.

Out of boredom, I got to looking at the build sheet from the dealer the previous owner bought it from... mostly to verify my gear ratio (4.30, hadn't looked to see that tow package meant that across the board)... and it said that I had the power rear window... and sure enough I couldn't see the button for it due to my look angle with the steering wheel.

Had started looking through junk yards to find wrecked CM cabs to pull it from. So... thanks to the previous owner, even if I didn't know that it was there from the get go.

I subject myself to expected ridicule... its worth it for not having to put it in myself - and I laughed at myself for a good half an hour this morning. Just wanted to share the laughs.

 

Stupid.*

*Legal disclaimer: Stupid comment not associated with any member's used tire purchase. Solely meant for not knowing that a CM had a rolldown rear window.

 

Updated headlights...thanks Roman/Cool Springs


2017 Limited


Black 2018 Led Headlights



Passenger is 2018 black vs Driver side is 2017 Limited



Both 2018 black installed



Side by side

 

Looks great! Same thing I did I love them

 

Do you have a link to this? Looks good. Also did you plasti dip the steering wheel badge and the dash?

 

I bought on ebay.ca (Canada) but this looks the same https://www.ebay.com/itm/Faux-Leather-Center-Armrest-Cover-for-14-18-Toyota-Tundra-Black/223166112928?fits=Model:Tundra&epid=26013189896&hash=item33f5bca4a0:g:q3cAAOSwlgFbrCU2:rk:4f:1&frcectupt=true

The cover isn't meant to have padding between, I used a thin sheet of packaging foam off one of my Amazon orders lol to make it cushier.

Yes, I took the airbag off, masked the badge surrounding it with newspaper and plasti-dipped it, that way I could just peel off around the badge and in the middle.

The steering control covers, vent rings, panel pieces on either side of the radio, cup holder, gear surround I removed, sanded and painted with Rust-oleum plastic primer and paint. The TRD shift knob I just masked and painted the same way.

Other than the badge, I don't recommend plasti-dip anywhere inside, it's not a nice smooth finish and nicks too easy.

 

Thanks, does the airbag badge pop off or is it stuck on with double side tape?

 

No, it doesn't come off, wish it did, that be easy. See nk's vid, removal of air bag here:



So that whole center piece was removed and in my garage, pretty much covered in newspaper except for the emblem, before I dipped.

It's awesome, no chrome/silvery distractions on the steering wheel.

 

Installed rear step for shorty lol

 

Looks great! Which one is that? My buddy has one on his RAM 2500, I like them.

 

Lights look awesome. Great idea on coating them first.

I may polish my bulge before bed