What have you done to your 2.5 gen Tundra today?

I had the Fumoto before this and really liked it. It just didn’t quite work with my current skid setup.

 

You can just swap the tube from the OEM plastic one. That’s what I had to do

 

Bilstein 8112 DSA+

 

These are the 8100 and 8112's from @memario1214

https://hotshotoffroad.com/collecti...-zone-control-cr-dsa-front-right-07-21-tundra

https://hotshotoffroad.com/collecti...pass-w-adj-resi-0-2-5-rear-right-07-21-tundra

 

Ok thanks!

 

Welcome back brother!

 

I actually have a t-shirt with that picture and that text on it. The wife loves it! Not...

 

It was a local guy here in Edmonton, found him on Facebook marketplace. Can't find the link anymore.

 

Appreciate it.

 

Mine weren’t. They were set exactly where they said they would be in the installation instructions (5/16” and 5/8” thread showing). Preset at 2.75” lift for a 4WD truck yet mine only lifted it 2”.

 

So you measured 5/16 and 5/8 and you only got 2 inches? I assume you took before and after measurements?

 

Yes and yes. 24” hub center to fender measurement. Same exact lift amount I had from the TRD Pro Fox coilovers- 2” lift.

I even went so far as to crank up the coilovers to their max height setting and that only netted 2.75” lift, not the 3.25” advertised (again on a 4WD truck).

I called Bilstein and they flat out said their product is hand made and can not have any faults. Between a supercharger and a 65 pound snow plow mount, my front end weighs 100-150 pounds over a totally stock truck. Bilstein dude said that minor weight increase might lower the front end by 1/4” and not 3/4”, and I would agree with that statement. Dude said I had to have installed them incorrectly and their product is not to blame. I do not agree with that statement.

 

My front bumper is 110 lbs or so and I didn't have any drops. I wrote my measurements from flares to ground on one of the boxes. I will have to look at it again. If I recall I'm at or slightly higher than where I was at with the Toytecs. There's really no way to install them incorrectly that I can think of. You can't put them on the wrong side without really messing something up.

 

Yeah I’m still waiting on your hub center to fender measurements….

 

Lol

 

I'll try to do it this weekend while I'm working on a couple of things. How do you like those UCA's? I currently have SPC's but I have a set of the DK's on order. I need to find out what the caster adjustment is at on those compared to the SPC since I currently have rub on the cab mounts. It would be nice if the DK's had maintenance free ball joints like the SPC's though.

 

Working on stereo stuff again
https://youtu.be/e2G0MA8xMFA?si=tq38uRXQlENCp2zW

 

The Dirt King UCA are a nice piece of metal. No complaints here. I didn’t want the maintenance or possible squeaking of urethane bushings and these have some fancy synthetic rubber that needs no grease. I also didn’t want to deal with uniball maintenance with our salted road winters. It does has the ball joint, it’s replaceable and greasable from the top under the DK cap. Im fairly certain it’s a common Moog ball joint.

And they are all maintenance free until they die. Even the sealed non greasables don’t last forever. I haven’t greased them yet as I’m too lazy to find out the specific grease type.

And I thought I read somewhere they add +1 degree of caster, but please verify that.

 

Here's the mod list the site had me get...

2019 SuperFast White Crewmax TRD 4x4 Sport, TRD Pro Grille, Toyota VIP glass break sensor, black badging, painted hood scoop satin black, driver grab handle, ceramic window tint, black mirror caps, ESP under seat storage, FRAC harness and camera, Katzkin TRD Sport Leather seat covers, Dasaita Android 13 Head Unit, AJT interior blackout, TRD Pro shifter, wireless console charger, ARB twin compressor, Victory 4x4 compressor mount, Morimoto XB LED Taillights, Morimoto XB LED third brake light, SCS 18x9x-18 F5 Wheels(5), 35/12.5 BFG KO2(5), Full Tufskin interior inserts, console safe, driver and passenger Swing-Away storage, Vortrak Tonneau cover, TRD Pro Skid Plate, TRD Pro Dual exhaust, Rago dash mount, Ram Mount for phone, Ram Mount for tablet, KC Rocklights, KC underhood lights, Amp Powersteps, Toyota blacked out led fog lights, Toyota bed mat, Desert Eagle catalytic converter shield, Falcon Sport Tow/Haul shocks, Coachbuilder +1 Shackles, REVESOL Sports leather steering wheel, Setrab transmission cooler, Cartrimhome auto up/down window switches, Spotter Mirrors, SDHQ Hidden winch bumper with Warn Evo 12-s.

 

Hell yeah.... I thought I had done alot but I believe you have me beat.Start a thread on your mods so you can keep up and put pics so we can see all that money.I started one ...Big Rick's Tundra Mods

 

I totally get it. This site made me purchase quite a few things already. It's also got me thinking I need the LC blower motor for improved air flow in the cabin and a transmission cooler lol

 

So many mods

 

Mr Ultimate Mod.....we ain't got sh@# on you

 

Bought a Banks iDash Pro to go next to the Innovate PSB-1, probably in this mount on the dash.

https://www.glowshiftdirect.com/universal-dual-gauge-console-dashboard-pod/

 

I’ve had mine for four years and a month. No issues. I love it. May go with an old man topper soon, though

 

Damn it.

 

I've had a Leer XR with windoors on both my trucks since 2012. I debate getting something new on the Tundra all the time, but having this all season water tight space is awesome. Old man or not, it works.

When my kid was younger, him and his buddies would sit back there and eat pizza before football practice. My guess is it'll evolve into his sleeping space with the dog while we're up top in a RTT.

 

What weight up top is that rated for?

 

Not sure. I've had a ton of stuff up there on a Prinsu rack. Leer used to offer a RTT but I don't think anyone bought it.

 

Damn.