Axle Good or Shot from Bad Repair? Rear Seal & Bearing Replacement Advice

Howdy everyone,

I'm in the middle of a rear axle seal and bearing replacement on my 2002 Tundra SR5 Access Cab TRD, and I’ve run into what might be a damaged axle shaft. Hoping to get some input from folks here who've tackled this job before.


Context:
This truck had a bad axle seal leak when I bought it. While tearing things down, I found that the brake backing plate, brake shoes, and the exposed portion of the axle housing were absolutely caked in gunk. Every nut and bolt was coated in grime. You can even see debris and buildup around the ABS tone ring and the axle shaft near the bearing and bearing retainer. The C-clip was stuck and took some extra effort to remove.

For the pressing operation, I followed Timmy the Toolman’s rear axle bearing video using Duane’s press tool and a 20-ton Central Machinery hydraulic press from Harbor Freight.


The Issue:
In Timmy’s video, after the first loud pop, the bearing and retainer press off smoothly and the axle shaft drops out cleanly. In my case, it went differently:

• I heard the initial loud bang, just like in the video.
• But after that, pressure builds again, followed by another loud bang — and this repeats multiple times, without much visible movement.
• I realized that there is marring on the axle shaft from what looks like a previous bad repair job. It seems the previous attempt was done by cutting the bearing retainer with a grinder or something, and I suspect that marring on the axle shaft surface might be causing the press to bind. More importantly, is the axle still good?

Here's a photo of the shaft with the visible damage:
>> Click here for full-size image <<


Questions for the community:

• Is the axle still usable given the visible marring?
• Could this interfere with bearing fitment or tone ring alignment?
• Does this area affect sealing or long-term reliability?
• Has anyone seen repeated loud pressure pops like this while using Duane’s tool and a 20-ton press?
• Would light cleanup (sanding, emery cloth) be enough — or is this a replace-it situation?

Any guidance or real-world feedback would be greatly appreciated. I’d love to avoid sourcing a replacement axle if I don’t have to, but I also don’t want to risk doing the job twice.

Thanks in advance for the help!
I’ll post updates as I go in case this helps the next person tackling this job.

—
Taha in Utah
Scout | 2002 Tundra SR5 4WD Access Cab TRD
273K Miles Strong | Rear Axle Seal + Bearing Refresh Underway
YouTube → Taha Abbasi – The Brown Cowboy

 

Well it does look like the tone ring was cut off and the axle scored. How deep is the cut?

Have heard of oil seepage under the inner retainer from scoring like it appears may exist lengthwise on that axle, but also heard of it being solved using like #2 permatex where the retainer mates to the axle shaft.

The outer retainer looks rusty and extremly pitted (meaning it's been exposed to moisture). Was the axle shaft pitted and rusty there too? Perhaps that is causing friction so making it hard to remove.

Here's what a 2023 OE axle with 200k+ miles looked like before disassembly. The outer retainer and axle shaft was not pitted with rust.

Could consider applying some penetrating oil at the mating surface of the axle/retainer before retrying to disassemble. Once apart could fully access condition of the axle.

If decide to replace and can't find a good OE axle, seem to recall someone replacing their axle recently with aftermarket, so maybe they can share more info.

 

When i helped @bmf4069 with his axle, i’m pretty sure the retainer popped, then came off smoothly. Maybe a file and some sanding would help yours, but i’m not sure i’d be comfortable running an axle with a stress riser like that. I’d find a whole axle housing from a jy and swap it (as long as its not caked in grease) instead of buying just an axle shaft, i think frank got his for $150 or so.

 

I think you're probably correct that the binding is being caused by inconsistency on the shaft surface, but wouldn't be at all concerned about it. Keep pressing. When you get it off, inspect the surface for any high spots. How far is the end of the groove from the end of the machined edge?

 

A this point I'd be tempted to go buy a JY axle, or better yet, just go buy a Dorman replacement that comes with everything, ready to press on...

 

Time for a Seqouia axle swap with disc upgrades.

 

Thanks for all the feedback everyone.

Seems it's a few mm deep. I can measure in the morning and share.

@shifty` I was thinking about this. At this point I've ordered:

1. Bearing
2. Inner Retainer
3. Outer Retainer
4. ABS Tone Ring
5. Inner Seal
6. Outer Seal
7. O Ring
8. and even the brake backing plate

All OEM. I'm wondering if I should return the items as I haven't installed any of them yet due to the issue I'm facing, and just get a replacement Dorman Axle as you suggested. How are these? I'll be doing some towing of side by sides, boats, jet skis, and overlanding to camp and lake sites here in Utah.



It looks like the Dorman one comes with Bearing, Inner Retainer, ABS Tone Ring, and Outer Retainer already pressed. Just need to replace Axel Housing Seal and O ring.

@KNABORES haha one day, I think it's too overwhelming to think about when I'm focused on fixing this axle seal leak for now and then work on suspension so I can go camping.

 

Or I could order OEM axle shaft lol...this truck is getting pricey

 

Maybe @shifty` or someone else has experience with that axle?

It looks like the inner retainer in the picture is installed too far outward not within like 3-5mm of the machined edge, but it's just a picture so maybe it's actually setup correctly. Might be able to reposition the retainer if needed. Don't know what bearing they use.

Can get OEM parts at almost 50% off during 25% sale off of online prices. Was able to source for about $105 a side. But when in a time crunch was also able to find the Nachi bearing and retainer set at Advance and Napa while using the other new Toyota bits (circlip, dust cap, o-ring, and axle seal).

https://www.tundras.com/threads/weird-rear-wheel-bearing-circlip-issue.144332/#post-3631838

Many reuse the tone ring.

Did you get it disassembled to see what shape the axle is in?

And why replace the backing plate? Is yours rusted away?

BTW have you read @remington351's thread?

 

I don't think you need to replace the axle. (as long as the groove doesn't extend to the edge/past the edge of the ABS retainer)