1. Welcome to Tundras.com!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all Tundra discussion topics
    • Transfer over your build thread from a different forum to this one
    • Communicate privately with other Tundra owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

2023 Tundra rims on 2006 Sequoia

Discussion in 'Sequoia 1st Gen (2001-2007)' started by gdisarray, Jun 17, 2025.

  1. Jun 17, 2025 at 7:23 AM
    #1
    gdisarray

    #1
    gdisarray [OP] Short term member

    Joined:
    May 26, 2019
    Member:
    #31028
    Messages:
    601
    Gender:
    Male
    Vehicle:
    2023 Tundra Limited HV
    Tint and wheels. Decked box in the bed. S and B Cold Air filters under the hood. Shiftpower throttle response controller.
    I just sold my old factory rims off my 2023 Tundra to a guy with a 2006 Sequoia. They have the same bolt pattern. 6 x 139.7. His guy says the hub is not fitting. Can something be shaved off to make it fit? He is a good hour and a half away so I can't go check what he is talking about. Bolt pattern is good, just hoping there is a shortcut to make it work.
     
    gdisarray, Jun 17, 2025
    #1
  2. Jun 17, 2025 at 9:55 AM
    #2
    Sirfive

    #2
    Sirfive Socially feral

    Joined:
    Jan 24, 2021
    Member:
    #58078
    Messages:
    5,387
    Gender:
    Male
    SATX
    Vehicle:
    ‘02 Limited AC TRD
    Bassani cat-back
    You need special hub centric spacers. 106.1 on the truck side 95.something on the wheel side.
     
    Sirfive, Jun 17, 2025
    #2
  3. Jun 17, 2025 at 8:27 PM
    #3
    gdisarray

    #3
    gdisarray [OP] Short term member

    Joined:
    May 26, 2019
    Member:
    #31028
    Messages:
    601
    Gender:
    Male
    Vehicle:
    2023 Tundra Limited HV
    Tint and wheels. Decked box in the bed. S and B Cold Air filters under the hood. Shiftpower throttle response controller.
    gdisarray, Jun 17, 2025
    #3
  4. Jun 17, 2025 at 8:42 PM
    #4
    Sirfive

    #4
    Sirfive Socially feral

    Joined:
    Jan 24, 2021
    Member:
    #58078
    Messages:
    5,387
    Gender:
    Male
    SATX
    Vehicle:
    ‘02 Limited AC TRD
    Bassani cat-back
    Nope, the wheel side of those needs to fit a 95.2mm hub. The hole in the center of the wheel is too small. Doofus shoulda known better, there was a guy who had some adapters made, but they werent cheap.
     
    Sirfive, Jun 17, 2025
    #4
  5. Jun 17, 2025 at 9:18 PM
    #5
    KNABORES

    #5
    KNABORES Sarcasm incoming

    Joined:
    Jan 1, 2020
    Member:
    #40572
    Messages:
    14,572
    Gender:
    Male
    Arkansas
    Vehicle:
    2000 Limited TRD AC 4X4 Thunder Grey 278k miles. *SOLD* 2019 Limited TRD CM 4x4
    Bilstein 5100's on the forbidden notch Husky HD rear leafs 16x8 Eagle Alloy 187's with 285/75/16 MagnaFlow 3" flow through Pioneer touchscreen with backup camera Full interior and dash LED conversion Trailer brake controller with 7 pin Bedliner coat bumpers & trim ARE Mpulse topper - Rhino Vortex rack
    Some non hub-centric hub spacers might work. Our wheels are technically lug-centric anyway. I’ve been running. Non hub-centric spacers on my FGT for almost 20 yrs. Can’t speak to compatibility with the 2022+ wheels, I know the lugs are different also.
     
    KNABORES, Jun 17, 2025
    #5
    Sirfive likes this.
Register FREE to Reply!

Products Discussed in

6x5.5 Hubcentric Wheel Spacers 1" for 1995-2023 Tacoma 4Runner, 6x139.7mm with 12x1.5 Studs 106mm Center Bore Forged Wheel Spacer for Tundra FJ Cruise Fortuner Sequoia GX460 GX470
$84.99
To Top