General Supercharger Thread

https://youtu.be/k-FrRyj9FQU?si=5q9Nu50oJOnHR2AY


@snivilous we need a billet trans pan with fins lol let me know if you want me to send you the b&m pan for scanning lol

 

This whole thread is so dangerous... It's like I swore I would only try weed once and now I'm researching how to do heroin.

 

So I think i'll order the HD valve body from cruiser parts and pass on the deep pan and plan on keeping the trans cooler pinned open 95% of the time. I'll switch to Dex III and change once a year. I'll plan on slipping under there and unpinning before i travel to colorado for ski trips.

That sound logical? I have a magnuson 2650 with stock pulley with a YotaWerx tune. Do not want to cook my trans so I'll do my best to stay on the stock pulley for now.

 

Are you out of powertrain warranty? I'm not trying to talk you out of using dex3 as WS type fluid has been used for years. Lots of unconventional things get posted and there are always risks.

 

I am out of factory warranty and understand there are risks, i do not like thin oils and accept i might screw it up. Sounds logical to me and i'm going to run with it!

 

Ok. Looks like there will be a few of us testing in "CONUS" how the dex3 does. I'm just waiting on my pan which should arrive next week. That was my thinking on the dex being a higher viscosity than WS type fluid.

 

@snivilous ram air scoop for trans?

 

Im now thinking of running brake cooling ducts from the front bumper area to the pan.. Have to look it over once I bring the truck over to the new place this weekend.

 

"I saw a baking pan cut in half and glued on once.
Looked surprisingly right."

https://www.reddit.com/r/cars/comme...od_scoops_were_weirdwhens_the_last/?rdt=58675

This made me laugh and question whether or not I'm throwing out the old bakeware from my mother's house. Seems like a cheap and easy way to test the Banks theory.

 

Haha. I was going to ask if it's OK to zip tie a spare storage lid underneath the trans and if it would hold up...

 

Just get a bigger trans cooler trying to cool a massive brick in the bottom would have marginal results I suspect.

 

Just being a smart ass with all the "improvements" we do to our trucks.

 

WAT sells a double cooler kit for the LC200s, maybe dual coolers would be a better option. They are just sandwiched together also, so should be easy enough.

 

Or even triple... if it gets that hot I'm in trouble. But can see it if I'm in the outback or Middle East.

 

LOL Coolers in the bed is the plan yes.

 

OK...OK...lots of coolers!

 

This just happened.

I can't get either AFR gauge to calibrate, both jump from 4.5-22/13. I have pulled them each 4x, swapped sensors, tried a third sensor in both. Any ideas?

 

But, isn't that the worst place for airflow? I guess if the fans are on all the time it'd be good? Looks awesome though!

 

Very common setup on these types of rigs no issues and on race vehicles they have no windshield so that helps. Low pressure area vacuum effect is my guess

 

its a rabbit hole for sure!

 

whats a good lil larger trans cooler upgrade?
even pinned i still run normal temps no less.
thinking a larger cooler esp after gears would be beneficial esp when traveling with/out the trailer

 

https://genuinecoolingsystems.com/

Lots of threads on this

 

Man! Not sure what's up. I thought of switching from AEM but my boost/afr gauge has been working well for the past 10 years. Only changed sensor out once. Hope you get it sorted.

 

And you can make your own for a lot less than genuine cooling.
If your plumbed into the condenser you can run the outlet from condenser to inlet on stand alone cooler then out to transmission for cheap or bypass condenser to stand alone cooler. Some use the

$59 Hayden 679 Universal 11” Rapid-Cool Add-On Transmission Cooler to Enhance Cooling (not for direct replacement of the factory unit)

Hayden 679 or ant 15-19 row cooler or bigger if it will fit.

 

I was just going to say this. No issues with my AEM units at all

 

thats what i was thinking, getting a bigger condenser as i have an 18 with stock trans cooler

 

go figure my rear bearing install kit is now delayed until april
trying to find a replacement near same price is like pulling teeth

 

Or just bypass the condenser and straight to external cooler. Could be causing excessive temps.

 

The lower priced kits are hard to find. Ordering from Japan should be here in about 3-4 weeks. But not complete kits.