What have you done to your 2.5 gen Tundra today?

Installed AJT shifter trims and ordered Rendline Goods leather shifter boot and a trd pro style shift knob.

 

Also threw the paddle board up top and took the kiddos fishing on the Columbia yesterday.

 

Front and rear dash cam installed. Someone rear-ended me last week, crumpled one side of the bumper and into the rear fender. He said I pulled over and within 5 seconds slammed my brakes. It was longer than that, but I did slam my brakes for geese in the road. Another driver stopped, got my info, and sent her dash cam footage to me. Shows the time elapsed, the geese, and that he was doing 15-20 over the speed limit and didn't apply brakes till within a couple car lengths. So useful, decided to pull the trigger on it.

 

Sickest DCs out there imo. Wish mine was one of em.

 

I have really been considering that Bamboo P1S.

 

I had that exact cam I think - sent it back within a week. In order to have this thing connect to your phone, you can't have anything else connected to your phone via WiFi. So if you have an aftermarket radio/head unit like I do, you're SOL. If it doesn't connect, you will not be able to use the app - meaning you won't have access to any videos unless you remove the SD card to watch them.

Note: I wish the rearview mirror port was hot without the key in ACC - the parking lot mode won't work when using it.

 

I don't have the space for another printer and don't want to try selling the Prusa. I'll probably just upgrade it, and anticipate that they get the firmware for the Mark4 sorted out sooner than later.

 

You sure didn't wait long after our convo lol... you'll have to do another tune though but I'm sure you won't mind

Congrats! I already told my wife i'm eventually getting one. She rolled her eyes.

 

They have hardwire wiring kits to enable the parking mode.

 

Yeah but it'd be super convenient to not have to run more wire when you have a power port in proximity like that.

 

LOL. Once she sees the cost of that I'll take your truck off of her hands after she buries you in the back yard.

 

I told her those three little words: separate bank accounts

 

Ugh...I'm good so far, I use Bluetooth (limited function) or USB-C to connect to my stereo...hope to upgrade to something that sounds better and is BT full function, but budget says I need to wait on that.

 

Ive been on that path with my original Ender 3 for a long while. It now has the sprite head, latest custom klipper, and runs off an octoprint Pi in a home built enclosure (lack table with leg extensions. Kits are all over thingiverse). And numerous other mods along the way or not listed.

Then I see the time prints take on that bamboo, along with quality level right out of the box, and damn. It makes me think, the 500 bucks and dozens of hours I have into over years, I should just spend 600 and grab a bamboo instead of putting more hours and money into this thing. I will still have this one to futz with. I'll move it to the garage to tinker if I go the Bamboo route.

 

Micro Center wants $850

Where do you see em for $600?

 

That is with the AMS. Bamboo itself sells the printer for 600 without the AMS, 850 with the AMS. You dont need the AMS, its a nice to have.

 

Haven't posted in this thread for a bit but just installed my Stillen CAI yesterday n took her for a drive around the block. The noticable difference is minimal as far as sound. Performance does seem to take a step up slightly. I got the oiled version but I don't want to put any oil filter on my Tundra so I bought the AFE dry filter plus the pre filter to wrap around it. So far I'm happy with it.


Question for anyone running this CAI... Were you able to keep your TRD air accelerator? If so, did you have to modify it?

 

You already had a CAI. How much was wasted on that one?

 

Enough to make him happy.

 

Just wanna give it a try n see if having that extra airflow makes any difference n didn't want to cut a hole in my fender. Being in California where this CAI is not CARB approved yet and finding it on OfferUp was somethin I didn't wanna pass up. I know the extra air intake may not make a huge difference with not being S/C but maybe someday i'll get there
I definitely could use something like this on my Taco however!

 

Always with the negativity…can’t go without something critical to say when you disagree with a post…refuse to be happy for someone…

See you next Tuesday.

 

Did RTCLMs - a roof-top canoe lumber mounts!





Water-tight wind-proof cover is in works. No, upside-down idea was considered and demised.

 

Are you going to swap to the stock box for your smog check and then swap back?

 

Yeah, unfortunately, i'll most likely have to do that. I do have a guy though that helps me with stuff like that but don't feel I wanna pay the hefty price when the swap is easy enough.

 

This sticky in the Performance subforum sums up CAI https://www.tundras.com/threads/official-intake-suggestion-thread.236/

Food fir thought. I paid 300.00 for one that now sits on a shelf collecting dust.

 

Finally joined the Dirty 7 Club!

Nitto Recon Grapplers 37x12.5x18.

 

Sick AF

 

Building a bumper for my 21 limited. Has led lights.

Not sure about the led driving lights.

Should I just source something else that is just as good or better?

I can cut these in with ease, but would love suggestions for options that exceed the factory units.

 

What about a set of pods like the Rigid SAE or Baja Designs?