What have you done to your 2.5 gen Tundra today?

I like this. Is there a link. How secure is this while driving?

 

It’s magnetic, very secure supper strong magnet. You can rack it in the holder, and pry down to break loose.

 

Got it on Amazon

 

Is your leg in the line of fire?

 

Parked next to a tacoma...

 

No

 

Foot maybe

 

Bought this knockoff TRD skid from Amazon. Tundra didn't come with one when I bought it. Probably one of the few times I've been surprised and impressed with quality for the price. It's thick aluminum, all holes lined up well, pretty stoked on the purchase.

$215 KUAFU Skid Plate Compatible with 2014-2021 Toyota Tundra 2020-2022 Toyota Sequoia Replacement for PTR60-34190 Front Lower Engine Undercover Guard Protection Aluminum Gray

https://www.amazon.com/dp/B0CBBSBYLV

 

Just to give ya a heads up, those jumper cables won't be a permanent solution. I learned the hard way myself

I made jumper cables into an extension cord of sorts for my boat, as I wanted to relocate the batteries to balance the boat weight more efficiently. I originally made them to just try out the setup, but after trying I loved it and figured I would let it ride. I put a breaker on to protect everything, but sent it other than that

The cord made it roughly 5 fishing seasons (my boat sleeps in my garage, as I lake hop, not stored in water at dock) and the trolling motor quit on me one morning. Took me a bit to figure out what it was, but it was the ultimately the jumper cables failing.

I cut them open to investigate and the entire inside was rotten.

Not telling you not to do it, just sharing my experience. I bought some marine grade wire in the same gauge and replaced it this summer. Was actually pretty cheap to do, shit I'm a cheap ass and had the jumpers on hand, so I went for it. Lol

 

Looks good, I like it Slap aTRD sticker on it n nobody would know the difference

 

I’ve contemplated getting one of those myself. Glad to hear it’s a nice product.

 

Anyone know if this can be done to the newer 2020 plus screens? I have this in my 2015, but I’m upgrading to the newer unit.

 

No it cannot

 

So have I , great price. Going to have to get me one now!

 

https://www.ebay.com/itm/185948491300
this one has a coupon available, takes it down to $200 shipped to Virginia!

 

Thanks! Bummer, but the bigger screen and Apple CarPlay will be nice!

 

Installed the TRD rear sway bar yesterday, and just finished the TRD front sway bar today. I need to buy a 1/2 impact because rear took me 2 hours and front took me three hours. So much time trying to get bolts off with a breaker bar. I left the front tow hooks off and will spray them red sometime.

 

Thanks for the link! Should be similar shipping to NC

 

Loaded up for truck stuff.

 

Daaamn!! Haha I just spent $188 shipped for that thing...wasn't even eyeing them but that's too good of a price and looks too good to pass up!! Thanks Tundra Forum Brothers/Sisters!!

 

Yall are going to like it, it's a beast. Pretty sure it's more thick than the OEM TRD. Directions pretty much suck but once you're under there it starts making sense.

 

Gotta find a good quality TRD sticker for it now.

 

You by chance coming to Arkansas to ride? I see a lot of people come here because of the National Forest, I'll be at Buckhorn tomorrow in my Honda Talon.

 

Kerrville. Buddy has 10 acres he’s been cutting trails on. Nothing too radical but get out from home for new years and ride and let the kids play. First ride with new belt, new springs, new tires, and a new carrier bearing. Lots of thrashing lately.

 

Just finished a 1300-mile round trip today. Approaching 58k miles. Such a great truck.

 

Installed Start-X remote kit the wife got me for xmas.

Pretty straight forward install with the video instructions (still nerve racking taking dash panels apart). Now im finally a kool kid with remote start to close out 2023!





‐--------> Bring on the 2024 mods!

 

Anybody install this with existing cat shields?

 

I have the Valhalla shield...we'll deal with whatever happens

 

How’s the lightbar output in the bulge? Do you feel like leaving the mesh in affects the light output?

 

For the sake of longevity and not stressing mechanical components should I let the oil pressure fall to its normal operating level and let the truck lower its high idle before I depart?