WHAT HAVE YOU DONE TO YOUR 3RD GEN TUNDRA TODAY?

Westcott preload collar front only to level front to stock rear.
Wheels are Rays Gram Lights 57DR-X 18x9 +20 in Dark Bronze.
Tires are Toyo Open Country AT3 D load range 35x12.5.

 

Brought truck to dealer yesterday (10Apr) to get TRD lift installed. Supposed to be a 14hr job, so I'm hoping it's ready on Thursday.

 

ouch 3k for parts and 1500 for labor probably

 

I brought the kit to them (purchased from Sparks parts $2600 shipped) and they quoted me a 14hr job at $105 per hr.

 

well at least you saved some money

 

Had TSB’s 110 and 111 installed this morning. Seemed to drive a little smoother leaving the dealer. see what it does for the occasional clunk starting and minor hesitation when cold after stopping.

 

Which one's are those? The only recalls I have is for the black screen and the tonneau cover (which I do not have).

 

Ditched the OCD overlay

 

They are not a recall, service bulletins.

https://www.tundras.com/threads/updated-04-06-23-ultimate-official-my22-tundra-technical-service-bulletin-thread-us-mex-can.117669/

 

Got my UCA installed today.

 

Any of you have strut mounts/top hats you want to part ways with? Looking for a pair

 

I saw it in the dealer prior to signing and sending it out for the mods, color match, etc.

woohoo, almost there

I will say the build quality looks to be improved from earlier ones I ve seen, panel gaps , alignment, etc were spot on

 

Finally put a little lift in. Rough country 1.75” up front, corn fed 1” in rear, Bora 1.25” wheel spacers. The rear now sits 1” higher than front. I like the stance Before and after pics. Now I might need bigger tires!

 

Got my steering wheel logo overlay and test fitting the trim overlay as well.

 

looks good. got a shot of it down the side with the spacers?

 

nice, is that the Toyota one? I’m looking for a front emblem one as well

 

Not oem, it's from taco vinyl

 

Rough country sport fender flares. Had to drill holes into all 4 fender flares to make it work with the rekgen mud flaps.

 

Sweet..!! How is the fit on the steering wheel overlay ? I’m thinking about getting this..

 

what size of tire is that, I got a 1.25” spacer for my 18” OR wheels for winter tires 275/70/18

 

Got the tri-fold tonneau removed by the dealership. I'm working with them to get reimbursed the cost of the tonneau.

 

The pieces fit real good around the buttons but it needs some trimming to get them to fit perfectly along the bottom.

Green lines represent area that wasnt being covered, Yellow is where it was overlapping on the leather.

Once I cut at the red line and trimmed a tiny bit at the blue lines, it fit perfectly.

 

Any issues so far? I had someone pose the idea that it helps mitigate turbulence for the mass air sensor. Idk but figured I would ask if you've thrown any codes.

 

@eddiefromcali where did you get the flat black steering wheel overlays. All I can find is gloss and carbon

 

..HMmm RC does not make t he Tonneau for 6.5 bed TUN ? I did not see on their site

 

Got it from Taco vinyl

 

Nice..!! Thank you ! I actually didn’t notice the overlay on the steering wheel spokes, I was referring to the blacked out Toyota emblem… the blacked spokes look better though I think.
I assume the logo piece is same dimensions as the ‘21 Tundra or Runner. Can’t find the ‘22+ Tundra listed for that item on the Taco Vinyl site…

 

This is the one I got. Perfect fit
https://tacovinyl.com/products/steering-wheel-overlay

 

good question! So far no change in mpg or CELs after a couple hundred miles since the air box “mod”. I went back and forth with OE air filters and the afe filter just to see if there was any turbo noise increase and both filters worked flawlessly.(fyi the afe dry filter and oe filter had very minimal noise differences).

Next mod is a tune to get the boostalaters boostalating more