What have you done to your 2.5 gen Tundra today?

I'm sold then...they're sitting in my Amazon wishlist until I get a chance to drop 'em into an order. Thanks.

That looks amazing. I'm worried those wheel might end up on my truck when I get new tires. I guess if you're only getting minor rubbing I shouldn't have any issues with the leveled front of the Pro.

 

Part number is:

it’s the one used in the SR Grade trucks

 

It is so minor and only at full lock. A bit on the front of the tire on one side and a bit on the back of the tire with the other one. Normal driving and even 90* turns at interaction give no rub.

We went 275/70 which is probably why and the Falkens seem to have quite an aggressive tread. I think 275/65 would have been fine, but we wanted bigger.

It is just touching the lugs of the tire. I'm confident raising up 1/2 and inch would eliminate it.

 

Just remember 2WD & 4WD have 2 different part #'s.

 

Finished installing the group 31 after receiving these @sleeoffroad battery terminal extensions.

 

Replaced OEM chrome tube steps with AL2 drop steps from Rough Country, and replaced chrome mirror caps with the silver ones. Very happy with both, and the installs were super easy too!

 

The rub must be because of the wheel offset. I have the same tires on stock aluminum rims and absolutely no issues.

 

The rims are 8.5" as well. There are likely a few factors causing the rub.

It's very minor and not a concern for me right now. But I will look to get rid of it.

 

Oh man that's perfect. That should fit a '20 TRD just sweetly

 

Just make sure you order the correct version.

 

Apparently regardless of the time I spent on SparksParts, I wasn't looking for the right thing. Perfect! Thanks for the advice

 

Ashamed to say it took so long, but finally had some time at home and away from work long enough to attack the sound system, dash and door speakers from @james@tech12volts.

I didn’t take as many pics as I could/should.
Simply put, the whole cab got the same treatment as the door in the pics below.

Stripped everything out, seats, carpet, door panels etc.
Put Kilmat over whole tub, back wall, doors (outer and inner skins), and underside of door panels. Then covered with Noico foam. Added a sheet of MLV to the floor.
Put a foam block behind all door speakers, as well as a foam surround.
Also went with a little custom set up on the rear tweeters, and placed them in the upper trim panels. My thought process was to keep them inline/level with the front sails.
I went with the Audiocontrol ACM 4.300 to push all the doors. The cool thing with the ACM series is, if/when I add a sub, I can add the 1.300 for just the sub, essentially creating a 5channel set up.
Beyond stoked with the new set up! Super clear, quality sound.

 

Did you paint the TRD bar or did you buy it blacked out? If bought, link to site if possible?

 

Paid the dealership $267 to replace a hose and clamp on the coolant crossover pipe because I was lazy. I took the truck in for the toyota care service (65k) and warranty repair to replace the noisy blower motor. Since the truck was there I just had them replace the hose and clamp for me.

 

Parted our my 2015 and installed this charger in my 2021, but with Android play, I just removed it today.....no more charger. It was a great mod or addition at the time even two phones later.

 

I have the Note 20+ and it's about 1/2" too long for the treat because of the shape. Believe me it was the first upgrade I tried to do ‍♂️

 

Installed Rigid 30 Radiance light bar with Rago bumper stealth bracket.

 

Awesome wish I could hear it!

 

Upgraded my license plate bulbs using a #921 from Alla Ligthing.

 

Installed my DD pods on my N-Fab MRDS bumper today. Everything went smoothly, no issues. Also decided to run my Limited grille for a while, giving the Pro grille some rest.

 

That grille looks really familiar. Where'd you get it?

 

Ohhhh man why did I have to see this.... looks great, been wanting to do the same

 

Got the AnytimeBackupCamera installed on the grille. I’m not going to badmouth the guy, but the install was annoying and long. It’s done and over with and I’m happy to not have to do it again. Very useless feature but hey.....I got it done. Lol

 

Never hurts to be prepared. A few first response additions

 

I need to mount my FE like this. Right now, it is rolling and clacking under the backseat.

 

Bought it from some crazy dude out of Tennessee if I remember correctly.

 

All my jomax goodies came in. Got the diff breather relocation installed. Ran out of day light for the rest. Have to love the winter dirt hah

 

Super easy with a self tapping metal screw. Solid as can be. That’s with the seat in full back position. Hides nicely under where I typically sit position.

 

Have a link for the seatbelt cutter?