What have you done to your 2.5 gen Tundra today?

where did you find it ?

 

Yeah it’s the 3/1 kit.

 

What trail lights are those? I like!

****edit....I read down and saw....****

 

@War Machine provided a link on a thread... will try and find it.

 

What size tires are on your Pro? Looks really good.

 

Thank you sir. 285/60/R18 toyo open country MT on stock rims, stock suspension.

 

Removed my flickering Amazon cool white visor and map/dome light led bulbs and replaced them with vleds in 5500k white to match my footwell lighting.

I like this color much better.

 

Ordered a Switch Pros SP-9100 yesterday on Amazon (through SDHQ) and got it today. Now I just need time to install it.

Any pictures of them being installed from the switch panel to the relay (?) panel to the lights would be welcomed.

 

Stayed up late last night to install the Decked bed storage system. I cannot recommend this product enough. It's going to make organization of everything I like to take along on trips so much easier.

 

This week I installed Husky Liners and a console organizer top and bottom from Amazon, had Line X Premium installed, and got a B&W Tow and Stow hitch that I will put on the truck once it’s back from the body shop next week to hopefully avoid more rear end accidents in the future.

 

Toyota Genuine OEM Black Chrome Exhaust Tip 2018 Tundra PT932-34180-02

$91 PT932-34180-02

https://www.amazon.com/dp/B07DT4TJBG/ref=cm_sw_r_cp_tai_sINWBb7D8Y9M3

 

Hey War Machine, I finally tried out the “Solution Finish” product for the black trims. Gotta say great recommendation on your part.

The bottle is a rattle can of sorts. Used your recommendation of using very little.
Once you put it on, you will want to wait a couple minutes to wipe it down again.

 

Trd duel pipes, 275/60R20 duratracs, sway bar. Not shown: bedliner, bed mat, soft cover, trd intake, tint, running boards .

 

Do you screw those into the side of the bed?

 

Me likey

 

I will say it for the second time today, this forum is a bad influence on my wallet.

 

Haha!

 

It made me laugh out loud!

 

OK, I must have been hiding behind the door when these came out. Nice little addition, and can you send me a direct link.

 

@poheller just happen to be selling I snagged em up, let me find my PM message of another member who in contact with the guy who makes em, appartenly the maker was on back order, give me a minute

 

Get with @lionix he in contact with maker, he sells through FB

 

@Skippy

 

Any rubbing with this setup? I'm planning on doing the same lift with the same size Ridge Grapplers.

 

I was rubbing hard on the front fender liner. I fully removed that. Mainly because I plan on getting a new front bumper soon. Other then that I was still able to keep my rear mud flaps! I also didn’t need a BMC.

 

Wiring will be another day as I have a lot that needs to be wired

 

LED amber turns in my 2018 LED headlights, but can't recommend them until I've had some longterm use. Built-in-resistors seem to heat and hyperflash for some. Left my hazards on for 10min, none so far. If you didn't do the amber delete mod and your ambers are always on, I'd avoid.






These may be better for you, couldn't find them on Amazon Canada. Or there's expensive VLEDs.

 

What is the best answer for this if I don't plan on switching bumpers? I know you don't want to remove the fender liner longterm. Where exactly did the rubbing occur? Sorry to bombard you with questions. Just trying to figure out my plan of attack ahead of time.

 

Planning on going with Ray10 18s which carry a +25 offset. Not sure how that compares to his Methods.

 

My wife found them on wish.com. Be prepared to wait a while on shipping. Took 3-4 weeks for them to arrive.