1. Welcome to Tundras.com!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all Tundra discussion topics
    • Transfer over your build thread from a different forum to this one
    • Communicate privately with other Tundra owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

Bilsteins in the front and rear?

Discussion in 'Suspension' started by Nor7, Mar 14, 2016.

  1. Mar 14, 2016 at 9:20 PM
    #1
    Nor7

    Nor7 [OP] Chilton Manual Guy

    Joined:
    Oct 19, 2015
    Member:
    #1989
    Messages:
    1,326
    Gender:
    Male
    Texas
    Vehicle:
    2007 Tundra Limited CM, 5.7L
    Ok, so I'm at 103,xxx miles and considering getting new shocks and springs.

    I'm going to get Bilstein 5100 but my question is this:

    Should I just do the front or is there any value in doing the back shocks as well?

    To those that have done the rear shocks, is there a noticeable difference? Seems like most of the performance (cornering, etc) is noticeable in the front, not sure if there's any value in upgrading the rear shocks.
     
  2. Mar 14, 2016 at 9:30 PM
    #2
    ColoradoTJ

    ColoradoTJ Certified tow LEO Staff Member

    Joined:
    Feb 24, 2016
    Member:
    #2766
    Messages:
    35,871
    Gender:
    Male
    Colorado
    Vehicle:
    LML 3500HD
    Calibrated Power 5 Tune pack, Allison 1000 tune, PPE deep trans pan, Cold/Hot CAC pipes, Banks CAI, PCV reroute, resonator delete, S&B 62 gal fuel tank, B&W GN hitch
    I would do the rear as well. Handling, braking, tire wear and your back will thank you.
     
  3. Mar 14, 2016 at 9:35 PM
    #3
    T-Rex266

    T-Rex266 Elon approved Staff Member

    Joined:
    Jan 5, 2014
    Member:
    #6
    Messages:
    156,394
    Gender:
    Male
    All 4 IMO. Better than the stock ride.
     
  4. Mar 14, 2016 at 9:35 PM
    #4
    Nor7

    Nor7 [OP] Chilton Manual Guy

    Joined:
    Oct 19, 2015
    Member:
    #1989
    Messages:
    1,326
    Gender:
    Male
    Texas
    Vehicle:
    2007 Tundra Limited CM, 5.7L
    Can you expand on this? From my experience, handling, braking and tire wear all are influenced and endured on/by the front tires.
     
  5. Mar 15, 2016 at 1:37 AM
    #5
    ColoradoTJ

    ColoradoTJ Certified tow LEO Staff Member

    Joined:
    Feb 24, 2016
    Member:
    #2766
    Messages:
    35,871
    Gender:
    Male
    Colorado
    Vehicle:
    LML 3500HD
    Calibrated Power 5 Tune pack, Allison 1000 tune, PPE deep trans pan, Cold/Hot CAC pipes, Banks CAI, PCV reroute, resonator delete, S&B 62 gal fuel tank, B&W GN hitch
    Handling is done by all 4 tires, not just two.
    Braking is also done by all 4 corners even though the rears do around 30%.
    Tires not staying in contact with the road due to bad shocks wears tires, effects braking/handling.

    Now a FWD car will wear tires up front faster. (Due to the drive axle/steering/most of the braking)
     
  6. Mar 15, 2016 at 4:48 AM
    #6
    csuviper

    csuviper Moderator Staff Member

    Joined:
    Jan 6, 2014
    Member:
    #38
    Messages:
    17,283
    Gender:
    Male
    First Name:
    Brian
    Broomfield, CO
    Vehicle:
    2019 TRD Sport CM 5.7L 4X4
    Some Mods :) See build thread for details
    All 4 will be better
     

Products Discussed in

To Top