1. Welcome to Tundras.com!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all Tundra discussion topics
    • Transfer over your build thread from a different forum to this one
    • Communicate privately with other Tundra owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

Snow Plow Setups (coils/shocks)

Discussion in 'Suspension' started by DarknessReigns, Jul 22, 2025.

  1. Jul 22, 2025 at 6:37 AM
    #1
    DarknessReigns

    DarknessReigns [OP] New Member

    Joined:
    Apr 28, 2019
    Member:
    #29777
    Messages:
    83
    Hey folks,

    I'm curious what the very few of you, who run a snow plow for winter, are using for front suspension on your 2nd gen Tundra's?

    I have a Western Midweight plow, coming in around 700lbs and I installed the Timbren bump stops, which helps, but the front suspension seems to be on the soft side.

    I have a BDS 4.5"lift, with the OEM front suspension. The OEM shocks are just slid into a sleeve to extend them.

    Have any of you run heavier Coil springs, shocks, other setups?
    Looking to get stronger coil springs, without lifting, since I am already lifted.
    Thanks,
     
  2. Aug 25, 2025 at 5:34 AM
    #2
    DarknessReigns

    DarknessReigns [OP] New Member

    Joined:
    Apr 28, 2019
    Member:
    #29777
    Messages:
    83
    Update for any future folks with the same question..I installed some of these Rubber coil spring spacers from Amazon (not the Sumo Spring overpriced ones) and the results are great. https://www.amazon.ca/dp/B0C46P8132?ref=ppx_yo2ov_dt_b_fed_asin_title

    Without any load on the front end, the truck already drives better and I feel way less road bumps. The OEM front coils on the 2ng gen area soft, so this helped tremendously.
     
  3. Aug 25, 2025 at 5:39 AM
    #3
    KNABORES

    KNABORES Sarcasm incoming

    Joined:
    Jan 1, 2020
    Member:
    #40572
    Messages:
    15,194
    Gender:
    Male
    Arkansas
    Vehicle:
    2000 Limited TRD AC 4X4 Thunder Grey 278k miles. *SOLD* 2019 Limited TRD CM 4x4
    Bilstein 5100's on the forbidden notch Husky HD rear leafs 16x8 Eagle Alloy 187's with 285/75/16 MagnaFlow 3" flow through Pioneer touchscreen with backup camera Full interior and dash LED conversion Trailer brake controller with 7 pin Bedliner coat bumpers & trim ARE Mpulse topper - Rhino Vortex rack
    So you’re running a heavy ass plow off the front of your truck that’s lifted with some sort of “sleeve” extension on the factory shock and now a rubber spacer thingy from Amazon. :der:

    You need higher spring rate front coils.
     
    whodatschrome likes this.
  4. Aug 25, 2025 at 6:02 AM
    #4
    DarknessReigns

    DarknessReigns [OP] New Member

    Joined:
    Apr 28, 2019
    Member:
    #29777
    Messages:
    83
    Nobody on planet makes higher rate spring coils for my setup.
    I have the 4.5" BDS lift, which uses the OEM front shocks and coils with a Sleeve extension.
    All aftermarket higher spring rate coils will lift the front end which I cannot have because of the 4.5" sleeve.
    https://bds-suspension.com/cdn/shop/files/BDS_Toyota_814FS_819FS.jpg?v=1752851769
     
  5. Aug 25, 2025 at 6:43 AM
    #5
    KNABORES

    KNABORES Sarcasm incoming

    Joined:
    Jan 1, 2020
    Member:
    #40572
    Messages:
    15,194
    Gender:
    Male
    Arkansas
    Vehicle:
    2000 Limited TRD AC 4X4 Thunder Grey 278k miles. *SOLD* 2019 Limited TRD CM 4x4
    Bilstein 5100's on the forbidden notch Husky HD rear leafs 16x8 Eagle Alloy 187's with 285/75/16 MagnaFlow 3" flow through Pioneer touchscreen with backup camera Full interior and dash LED conversion Trailer brake controller with 7 pin Bedliner coat bumpers & trim ARE Mpulse topper - Rhino Vortex rack

Products Discussed in

To Top