General Supercharger Thread

You should just drop it off @snivilous let him go through the thing

 

I'm working on a teleportation device in my spare time.

 

It's amazingly well packed is the positive. No way without cutting/ moving the washer fluid reservoir will this monster fit.

 

I wonder if @snivilous can scan something up and one could print a "form-fitting" tank/reservoir around the new tank? That thing is YUGE!

 

Now that's a big brain idea I can get behind, Tundra specific oversized coolant tanks. That would be pretty sick! And I did just get a 5x10 sheet of aluminum and steel in today

 

Where exactly are you guys putting bigger tanks? Looking in the engine bay there's no decent room. My three initial ideas are a tank that forms around the ECU area behind the intake box, or in front of the intake box but then you need to still access the steering reservoir and dip stick (plus usually where the catch can goes), and third is a dual tank setup where it fits where the windshield washer reservoir is and then relocate that as a custom tank behind the airbox.

Granted the stock intercooler reservoir is tiny so wouldn't need much to get a lot more fluid, but I was hoping there was an "easy" way to have like a gallon or more in just the reservoir.

 

You could get an SDHQ washer reservoir like I have below, if the 4Gal would fits where the stock washer res is, that's a big box. Or work on the Lexus washer res like @Mdl is doing.



Would it fit on the driver's side on a dual-compressor mount that sits above the fuse/relay box? Or is it too tall?

You could always mount it elsewhere and keep the Maggy res as the fill port.

 

The 1.5 gallon I got from Viktor shoehorned between the airbox & firewall.

It's cap isn't vented (and broke) and I was getting a vacuum after filling the hole Viktor drilled because it was dribbling coolant.

 

Two options for folks not everyone wants a large tank some do. I’d say the multi tank unit is a solid option. We used to this for the cobras. Then then those that want a larger unit can do the large box maybe with a battery relocation or where army has his

 

I’ll take dual unit lol @snivilous

 

Using the LC washer fluid reservoir, as a washer fluid reservoir, is a great idea. Especially if it keeps factory sensor/computers happy. That would open up the entire front area for a ram air type of setup and then make space for whatever else on top of the inner fender. Just a thought. I know a lot of you are already opening up the inner fender to get to the air, but doing a more open Stillen front intake type of deal, directly into a box could be a space saver and add a bit of air flow, too. Selfishly, I'm hoping someone says it's not a horrible idea.

 

The LC fits in driver side fender. Just gotta fab it up. I'll try and mock it up again and hog out the filler neck in fender. A prospeed style 2.5 gallon tank fits where the washer bottle is could be a little bigger. Has the steering pump attachment. I've even seen a few 3gal fuel cells that are about the same size for $82.

 

Sooooooo

sniv looked at my log, I have 0 volts at the MAF wheeeee.

I have a sub 20 mile OEM MAF, a sub 2k mile OEM MAF, a sub 1k mile TK MAF & an old from my '10 Tundra JET POS that was in the truck for 20 seconds on a Bully Dog tune. Only the JET gets any voltage sporadically & that's low.

The connector came back from the 1st motor minus its "fastner pin" and has been on & off more MAFs then I can remember I pushed all the pins down without change, I ordered a new connector with early am delivery so will solder it in in teh morning.

$16 Mass Air Flow MAF Sensor Connector Fits for Chevy T7500 W3500 Tiltmaster, for Toyota 4Runner Avalon C-HR Camry, for Lexus GS350 GX470, for Pontiac Vibe, for GMC T6500, for Isuzu FTR, for Scion TC

https://www.amazon.com/Sensor-Connector-Tiltmaster-4Runner-Pontiac/dp/B0DT6XSCPQ?crid=X47WE78IZWRI&dib=eyJ2IjoiMSJ9.ZUNnfiEeEgTSj3e9X85qNV_iOi9HqGWK4Ja5CkLGB0nnUYAAYQ8ayk6JaCDJqH3h0xgofWrxSVScb812itTf9_GVWVChaeY3AmhJKs_FZGXqjdRSn0U1xRMBrdnzSdAb_A8ypiMvHhQMIXOGLe8SDOBMNE-3yh21sLMwAb5g3xGWyDSOzlDPKnzgyXmIcf5TDJUjfGBVJ_j-CyXTLgam_AO6M3yNXbVhPfjtM0q7h9o.Ehry5dHGJHrgg7hAfAcHvnt8xUY88Xvg8TNaQ5NHaGE&dib_tag=se&keywords=2007-2021+Toyota+Tundra+Mass+Air+Flow+%28MAF%29+Sensor+Connector&qid=1754342760&sprefix=2007-2021+toyota+tundra+mass+air+flow+maf+sensor+connector+%2Caps%2C256&sr=8-1

 

I suspect this is a first motor swap installer issue? Isn't that when they were chasing electrical issues? If the harness doesn't work, testing wires to the ECU?

 

Yes, they fucked up the connector at the ECU & eventually fixed it.

 

"...fixed..."